PDA

View Full Version : Repaired MFPB c368


Custom Search


arahael
02-04-2019, 11:50 AM
Hello. I ordered refurbished mfpb for c258. After replace board swapped eeprom1/2, emmc, enter correct machine type, used reset tool, update firmware/boot, machine dropping c163/c164, any sugestions ?

kingarthur
02-04-2019, 12:42 PM
If the codes are CC163/CC164 , the manual says wrong model of FW, the machine type information registered to the machine differs from the actual machine type

qbert69
02-04-2019, 12:42 PM
Hello. I ordered refurbished mfpb for c258. After replace board swapped eeprom1/2, emmc, enter correct machine type, used reset tool, update firmware/boot, machine dropping c163/c164, any sugestions ?Error Codes > Konica-Minolta > bizhub 130f > page 1 (http://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub) C368&code=CC163

Error Codes > Konica-Minolta > bizhub 130f > page 1 (http://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub) C368&code=CC164

Apparently something is not quite right!!![emoji848]

Sent from my SM-N950U1 using Tapatalk

arahael
02-04-2019, 01:03 PM
I send back mfpb. Data on MFPB can be corruped. I must wait to resend new. Thanks

byronf
02-04-2019, 05:09 PM
I am also stuck with the same issue, I have replaced mfp board, emmc & EEPROM but the issue still persist's. The only thing I haven't try was the reset tool, do you mind sharing it with me please.

Synthohol
02-04-2019, 11:01 PM
1. This error may occur after flashing the MFP firmware. It signifies a ROM contents faulty error due to incorrect or corrupted firmware being installed.

Reinstall the firmware verifying that the firmware file and checksum corresponds to the correct machine. The latest version firmware or system software is available via the Konica Minolta Download Selector.

This error may occur intermittently after replacing PWB-MFP. It is possible the ribbon cable on PWB-MFP was not fully seated.
Remove and reseat the ribbon cable on PWB-MFP.

double check the machine type based on the serial# not the model.

bit sw 25 settings based on serial.

http://www.copytechnet.com/forums/attachments/konica-minolta/41632d1549321282-repaired-mfpb-c368-sw25-jpg

escalante
02-05-2019, 02:55 AM
In this photo, it refers to the code CC-163 and CC-164https://uploads.tapatalk-cdn.com/20190205/769404c965f856b701efbfff0e1273b0.jpg

Enviado desde mi SM-J701M mediante Tapatalk

arahael
02-05-2019, 12:53 PM
i can't find gg9 firmware anywhere. also on my infohub. can you?

Synthohol
02-05-2019, 01:18 PM
Version GG9-84 under special FW
bizhub C258, C308, C368 Special Firmware Version GG9-84 Boot ROM Version G00-02 and Screen calibration

arahael
02-05-2019, 02:59 PM
Version GG9-84 under special FW
bizhub C258, C308, C368 Special Firmware Version GG9-84 Boot ROM Version G00-02 and Screen calibration

I can't find anywhere ffs :( Im using DEVELOP dbox site its makes me sick to find anything mate.

canerk
05-01-2019, 09:02 PM
gg9-84 bulabildinizmi
bu güncellemeye benimde de ihtiyacım var

canerk
05-02-2019, 10:12 PM
GG9-84 yazılımı nereden bulabiliriz.

canerk
05-02-2019, 10:14 PM
a789be.tar dosyası makinada hiçbir tepki vermiyor.

tulintron
05-06-2019, 03:59 PM
Good morning. By the way, did you try to change the speed up of the equipment?

Phil B.
05-06-2019, 04:23 PM
GG9-84 yazılımı nereden bulabiliriz.

the rest of the posts here are in english...

could you be so kind as to follow the leads of other?

canerk
05-06-2019, 06:48 PM
[QUOTE = tulintron; 752511] Günaydın. Bu arada, ekipmanın hızını değiştirmeyi denediniz mi? [/ QUOTE]

evet her şeyi denedim.
.tar dosyasını okuyamıyor makina

gg9-84 bellenimi gerekiyor. fakat bulamadım bu bellenimi

teşekkürler.

tulintron
05-07-2019, 02:36 PM
[QUOTE = tulintron; 752511] Günaydın. Bu arada, ekipmanın hızını değiştirmeyi denediniz mi? [/ QUOTE]

evet her şeyi denedim.
.tar dosyasını okuyamıyor makina

gg9-84 bellenimi gerekiyor. fakat bulamadım bu bellenimi

teşekkürler.The rest of the posts here are in english...

could you be so kind as to follow the leads of other?

canerk
05-13-2019, 02:17 AM
okey
where can ı get my gg9-84 firmware

help please

Custom Search