View Full Version : Faded on edge
positiveg
11-28-2020, 01:10 AM
Hey guys I'm getting some colour fading in the edge of my 12*18 prints
Please check this scan image please.
Check k out the green bar on the top and bottom set of labels.
Think could be the IBT or the fuser?
Thanks
And I did Ave a line running through. Thought came from the yellow drum so I changed it. Don't seem like it was that drum.
https://uploads.tapatalk-cdn.com/20201128/7e2326daf92189281569b224b7c101fd.jpg
Sent from my SM-G955F using Tapatalk
Phil B.
11-28-2020, 01:41 AM
Hey guys I'm getting some colour fading in the edge of my 12*18 prints
Please check this scan image please.
Check k out the green bar on the top and bottom set of labels.
Think could be the IBT or the fuser?
Thanks
And I did Ave a line running through. Thought came from the yellow drum so I changed it. Don't seem like it was that drum.
https://uploads.tapatalk-cdn.com/20201128/7e2326daf92189281569b224b7c101fd.jpg
Sent from my SM-G955F using Tapatalk
need it in PDF format
what are the life counts on the drums/dev units?
OEM genuine Toner/drums/devs?
direction of feeds on the PDF examples?
did you try a copy of the example? different issues?
what are the life counts for fuser/ITB?
what media is being run?
is the media properly setup on the unit trays?
what tray are you feeding from?
Phil B. ' The Dentist '
positiveg
11-28-2020, 02:19 AM
All genuine drums and to ers.
Fuser on 38% got to check te count
Black drum 96
Yellow drum just installed today M, C 96%
Ita an adhesive vinyl 4 mil stock running from trya 5.
See I was gonna save the scan in Pdf and was like nope jus in case would get asked for it in JPG.
Lol
Sent from my SM-G955F using Tapatalk
CP-1015
11-28-2020, 10:17 AM
Hi, already calibrated?
copier tech
11-28-2020, 10:45 AM
All genuine drums and to ers.
Fuser on 38% got to check te count
Black drum 96
Yellow drum just installed today M, C 96%
Ita an adhesive vinyl 4 mil stock running from trya 5.
See I was gonna save the scan in Pdf and was like nope jus in case would get asked for it in JPG.
Lol
Sent from my SM-G955F using Tapatalk
Swap round the yellow & magenta drums around see if this 'moves' the issue.
positiveg
11-28-2020, 11:04 AM
Hi, already calibrated?Yeah, but I'll run another
Sent from my SM-G955F using Tapatalk
positiveg
11-28-2020, 11:04 AM
Swap round the yellow & magenta drums around see if this 'moves' the issue.Ok cool will give this a shot and see
Sent from my SM-G955F using Tapatalk
blackcat4866
11-28-2020, 02:40 PM
47433
This is not the easiest sample to use for color differentiation, but from what I can tell all the colors are ~40% less density across the board. So ... IF there is a single cause, it's a problem affecting all colors equally, i.e.: primary or secondary transfer, or maybe all of the laser slit glasses equally dirty at the rear. It's unlikely that all the imaging units are experiencing the exact same fault in exactly the same location.
If you'd like specific advice, you might tell us what model of machine that you have.
Make it easier on yourself! Use a print sample using CMYK base colors like this:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.