View Full Version : tape problem on PC417
hello I allow myself to create a new thread because I have a problem on two pc417 modules, tray number 3 create jams on two identical copier a bizhub c450i I change the 2 modules but the two new ones do exactly the same thing I changed the paper plugs, changed the sensor, I ran out of ideas
copier addict
03-25-2021, 05:36 PM
hello I allow myself to create a new thread because I have a problem on two pc417 modules, tray number 3 create jams on two identical copier a bizhub c450i I change the 2 modules but the two new ones do exactly the same thing I changed the paper plugs, changed the sensor, I ran out of ideas
What jam code is being generated?
Where is the paper stopping?
Are there any nicks, or paper being crumpled?
Albonline
03-25-2021, 06:18 PM
4869948699
cause of this is lack of or insufficient pressure on those two white rollers in the photo. The df torque limiter in this system is really tight.
Synthohol
03-25-2021, 10:28 PM
JAM CODE?
[QUOTE = Albonline; 1718042] la cause en est un manque ou une pression insuffisante sur ces deux rouleaux blancs sur la photo. Le limiteur de couple df de ce système est vraiment serré. [/ QUOTE] hello how to fix this ?
[QUOTE = copieur addict; 1717946] Quel code de bourrage est généré?
Où s'arrête le papier?
Y a-t-il des entailles ou du papier froissé? [/ QUOTE]
hello I put a photo of the place where the paper always gets stuck
Synthohol
03-26-2021, 01:44 PM
without revealing the actual jam code is like going to the dentist but wont tell them which tooth hurts.
help US to help YOU.
photos are irrelevant without the jam code.
wheres the "dentist"? lol
Albonline
03-26-2021, 02:33 PM
[QUOTE = Albonline; 1718042] la cause en est un manque ou une pression insuffisante sur ces deux rouleaux blancs sur la photo. Le limiteur de couple df de ce système est vraiment serré. [/ QUOTE] hello how to fix this ?
i push down on the ends of metal bracket holding the rollers. deforming enough to apply a bit more pressure. have fixed dozens of these doing only that. if you have been putting your fingers all over the feed tire system i would also clean with ipa.
mojorolla
03-26-2021, 02:37 PM
Did you configure the LCT (go into Service Mode, System 2, LCT and set the paper sizes) ?
:)
i push down on the ends of metal bracket holding the rollers. deforming enough to apply a bit more pressure. have fixed dozens of these doing only that. if you have been putting your fingers all over the feed tire system i would also clean with ipa.
+1 for the bracket adjustment, we also had some PC417 jamming directly out of the box
[QUOTE = Albonline; 1718042] la cause en est un manque ou une pression insuffisante sur ces deux rouleaux blancs sur la photo. Le limiteur de couple df de ce système est vraiment serré. [/ QUOTE]
thank you that was it
thank you to all the problem is located at the level of the white pressure roller, the problem was quickly resolved with your valuable advice
tsbservice
03-26-2021, 08:17 PM
without revealing the actual jam code is like going to the dentist but wont tell them which tooth hurts.
help US to help YOU.
photos are irrelevant without the jam code.
wheres the "dentist"? lol
You don't need our friend to pull some tooths when Zen-Uber KM master speaks :)
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.