KM paper size sensor VR1 adjustment

[sunsetoutpost]

You guys are pretty smart, someone has to have figured this out. How can I set (fudge) the meshing of the VR1 gear so it registers the correct paper size? I've already had the drawer apart twice (remove lift motor, wires and lift plate) in order to get to the darn thing. Why doesn't the SM give a resistance measurement for a specific paper size so I can just take this apart once?

[tsbservice]

You guys are pretty smart, someone has to have figured this out. How can I set (fudge) the meshing of the VR1 gear so it registers the correct paper size? I've already had the drawer apart twice (remove lift motor, wires and lift plate) in order to get to the darn thing. Why doesn't the SM give a resistance measurement for a specific paper size so I can just take this apart once?

And machine model is?

[sunsetoutpost]

And machine model is?

DI850

[sunsetoutpost]

Swapped VR1 with another machine, same result. Going to look deeper.

[Flash]

It has been a while since I have worked on a crusty old Di850 but there should be a tray size adjustment in the service mode.

[blackcat4866]

Most other KMs have a calibration in service mode. I don't know for sure about the DI850. =^..^=

[Synthohol]

n


1
Enter th
e 36 mode.


2
[Adjust
Press "
ment mode menu Screen]
Image adjustment".


3
[Image
Select "
adjustment mode menu Screen]
Tray adjustment".


4
[Tray a
Press th
select t
The scr
1 (2) to
to Tray
Using a
(the inn
plates o
and to 2
Set the
faces of
pass tra
280 mm
djustment Screen]
e or key to
he tray to be adjusted.
een changes from Tray 1 (1) to Tray
Tray 2 (1) to Tray 2 (2) to Tray 3 (1)
3 (2) to By-pass 1 to By-pass 2.
scale, set the distance between
er surface of) the paper side guide
f each tray to 250 mm on Tray (1),
80 mm (8.5x11) on Tray (2).
distance between (the inner sur
) the paper side guide plates of by
y 1 to 210 mm (A4R) and tray 2 to
(8.5 x 11) respectively.


5
Press t
The sel
adjuste
After ad
displaye
he key.
ected tray is automatically
d.
justment completes, a message is
d.


6
Press t
he key

[sunsetoutpost]

[QUOTE=Synthohol;2104233]

n


1
Enter th
e 36 mode.


2
[Adjust
Press "
ment mode menu Screen]
Image adjustment".


3
[Image
Select "
adjustment mode menu Screen]
Tray adjustment".


4
[Tray a
Press th
select t
The scr
1 (2) to
to Tray
Using a
(the inn
plates o
and to 2
Set the
faces of
pass tra
280 mm
djustment Screen]
e or key to
he tray to be adjusted.
een changes from Tray 1 (1) to Tray
Tray 2 (1) to Tray 2 (2) to Tray 3 (1)
3 (2) to By-pass 1 to By-pass 2.
scale, set the distance between
er surface of) the paper side guide
f each tray to 250 mm on Tray (1),
80 mm (8.5x11) on Tray (2).
distance between (the inner sur
) the paper side guide plates of by
y 1 to 210 mm (A4R) and tray 2 to
(8.5 x 11) respectively.


5
Press t
The sel
adjuste
After ad
displaye
he key.
ected tray is automatically
d.
justment completes, a message is
d.


6
Press t
he key


Awesome, I'll give 'er a try

[sunsetoutpost]

All good now, don't know how I missed that in the SM. Guess that's one that I hadn't run into before. Thanks to all