K7135(IP423) display E87-3 error code

[kmcopytech]

K7135 install IP423, shows error code E87-3;

replace hard drive(2GB compact flash card and PCMCIA adapter).

After the replacement of the boot, IP423 Can't complete initialization.

moments later displayed:

"Printer board failure, Press auto to bypass Printer function,
Please call service."


Are not a print controller software were destroyed???
Reinstall the print controller software can solve the problem?

Note: The IP (print controller) system code must be upgarded to a minimum version of 5.9.0 to support the use of CF card ,

I overlooked this point....:mad:


Now need IP-423 firmware ver5.9.0.

Who will help me ?????

My E-mail: kmcopytech@gmail.com


thanks!!!!!

[pepper38_cnd]

Is you IP just PCL or PCL & PS? It doesn't matter here is the system code for both. Also the 2G compact flash card you installed must be formatted with FAT ( Not FAT32 ) before installing. Also I can't remember on that Ip if the system card has to be formated with VXworks. If you rewrite the firmware and still have problems you may have to look into that.
https://download.yousendit.com/Y2ovYUlxV3JveE1LSkE9PQ

[kmcopytech]

Is you IP just PCL or PCL & PS? It doesn't matter here is the system code for both. Also the 2G compact flash card you installed must be formatted with FAT ( Not FAT32 ) before installing. Also I can't remember on that Ip if the system card has to be formated with VXworks. If you rewrite the firmware and still have problems you may have to look into that.
https://download.yousendit.com/Y2ovYUlxV3JveE1LSkE9PQ


Thank you very much!!!

Found the problem,

Before installing,

1\The PCMCIA hard drive are viewed after following this procedure by using the PCMCIA slot on my windows based laptop,and formatted to become FAT .

2\Displayed printer board failure message after! Technicians also formatted the 32M system memory card in WINDOWS XP:mad:!

Now:

1\Run HyperTerminal (Connect an RS-232C Serial cable between the PC and the IP423 print controller).

2\If reformat the CF card to VxWorks style formatting. Can resolve this problem???


Thanks again!!!

[kmcopytech]

Run HyperTerminal on the PC, use the RS-232 (DB9) to connect PC with the IP423 print controller, open the copier power, the self-test is as follows, can not be completed, unable to enter the VxWorks system,

Why????? system compact falsh card is failure?


=== Power On Self Test ===
Disable NMI
Reset Coprocessor..
Disable Shadow.
Init Cmos Memory..
Test Timers
Start Refresh DRAM
Check DRAM Amount
Test Base 64KB Memory
Clear Base 64KB Memory
Enable L1 Cache
Enable L2 Cache
Init BIOS Data Area.
Init Interrupt Controller
Init Interrupt Vector Table.
Enable Timer Interrupt..
Init PCI...
Enable Shadow.

Konica Corporation IP-423/IP-432 : BIOS Version 1.01
Embedded BIOS (tm) Version 4.3
Copyright (C) 2000 General Software, Inc.

Disable L2 Cache
Disable L1 Cache
00000640K Low Memory Passed
00064512K Ext Memory Passed
Check Key In..

PCI Device Table
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 7190 Host Bridge
00 01 00 8086 7191 PCI-to-PCI Bridge
00 07 00 8086 7110 ISA Bridge
00 07 01 8086 7111 IDE Controller
00 07 02 8086 7112 Serial Bus 10
00 07 03 8086 7113 PCI Bridge
00 11 00 4B43 505E Konica PCI Device 11
00 12 00 4B43 5859 Konica PCI Device 3
00 12 01 4B43 5859 Konica PCI Device 3
00 12 02 4B43 5859 Konica PCI Device 3
00 12 03 4B43 5859 Konica PCI Device 3
00 12 04 4B43 5859 Konica PCI Device 3
00 12 05 4B43 5859 Konica PCI Device 3
00 12 06 4B43 5859 Konica PCI Device 3
00 12 07 4B43 5859 Konica PCI Device 3
00 13 00 4B43 5050 Konica PCI Device 5
..
Test Hard Disk Drive.
Init Coprocessor
Enable Cache Memory
Enable Coprocessor INT & NMI...
Enable Clock Ctrl
Boot!


Remove disks or other media.
Press any key to restart

Have any way, Help me!!!

Thanks!!!

[pepper38_cnd]

Here is the procedure, I hope this helps

[kmcopytech]

Thanks!!!

I operation in accordance with this procedure too,
but can't enter the service DOS !

Haha!
God bless!!!........

[kmcopytech]

Problem solved! Share: :p,
can't ENTER service DOS!!! ????

1 \ To create a DOS6.22 boot disk (floppy disk or CD-ROM);

2 \ VxWorks system installation method and the same!

3 \ IP423 system ver5.9.0 copy to D: \ IP423V590;

4 \ Edit a IP423.bat, reads as follows:(Disk F: is system CompactFlash card),

@echo off
ECHO Formatting partition #1(F:.......)
a:\format F: /v:KONICA-IP <YES
if errorlevel 1 goto error

ECHO Installing IP-423 boot loader .......
lock c: <YES
D:\vxsys F: <YES
if errorlevel 1 goto error

ECHO Installing IP-423 bootrom.sys ......
copy d:\IP423V590\boot\bootrom.sys F:
if errorlevel 1 goto error

ECHO Copying IP-423 firmware ......
a:\Xcopy d:\IP423v590\ F:\ /E /H <NO
if errorlevel 1 goto error

goto end
:error
ECHO **********************************
ECHO Please chick command..........
ECHO **********************************
beep2

goto end
:end

Copy after the completion of the installation of IP423, connected RS-232 crossover cables, Power on test, as follows:

[kmcopytech]

pepper38 cnd:

Thanks again!

You are the best! ... ...