PDA

View Full Version : How to deal with KONICA MINOLTA COLOR FORCE 8050 Report Code SC29-07 ERROR ???


Custom Search


mamianda
03-21-2010, 07:29 PM
I own a KONICA MINOLTA COLORFORCE 8050 machine and every time I turn it on, it prompts the following error message on the display screen:

Report Code SC29- 07
Tel - 0000905-890-1005
Fax- 0000905-890-4608

CAN SOMEONE TELL ME ON HOW TO RESOLVE THIS ISSUE? Or What could be the result of this error message? THanks in advance!

RRodgers
03-21-2010, 07:39 PM
Have ya tried to just turn it off (both switches) and turn it back on?

mamianda
03-21-2010, 07:47 PM
Yes, I tried shutting off BOTH swtiches and back on. It still didn't work. Any suggestions??
Thnx.

jotunn
03-21-2010, 08:31 PM
Clean up the Gamma sensor on Image Correction Unit, then try to turn machine off and on.

mamianda
03-22-2010, 12:18 AM
@ Jotunn- I'm not exactly sure where the Gamma sensor is located nor the Image Correction Unit. (Would you be able to send me a picture showing that so I can take it out and clean the sensor)? Please let me know. Or direct me to it. ??
Thanks!

jotunn
03-22-2010, 01:48 PM
Gamma sensor is located in the area surrounded by red ellipse on the photo - this is a module with couple of shutters.
37943795

florinliber
03-24-2010, 08:33 AM
Hello,

I have the same code error Sc 29-07 on CF 8050 machine,
cleaning the sensor does not solve the problem
What else I can do ?

jotunn
03-24-2010, 09:40 AM
That's interesting:

Revision of Print control program (Ver. 20 => Ver. 30) Image control program (Ver.20=>30) and Operation program (Ver.20 => 30)

2) Correction of IP-901 related failures
k. When the consumable reaches to over half of the life expectancy and the environment changes, SC29-07 may occur.

So maybe firmware update can help

florinliber
03-24-2010, 11:22 AM
jotunn = thanx for response

pls help me to understand how to do that.

I recently did gamma autoadjust from 3 6 mode and result was SC error code 29-09

RRodgers
03-25-2010, 06:49 AM
jotunn = thanx for response

pls help me to understand how to do that.

I recently did gamma autoadjust from 3 6 mode and result was SC error code 29-09

Check to make sure your Dev's are ok and not leaking out the sides.


F29-09 Dmax control /C resulted in an
abnormality.
Printer control board (PRCB)
Developing unit /C
Gamma sensor (PS11)

I've seen the gears wear out on the dev units as well, causing all kinds of probs.

mdar
10-14-2013, 11:08 AM
error code sc 29-07There is a problem with this code Please help if there is an effective solution Program has been used1. Enter the 36 mode.2. "36 mode menu screen"Press the[3. Image quality adjustment] key.3. "Image quality mode menu screen"Press the [2. Printer gamma adjustment] key.4. "Printer gamma adjustment menu screen"Press the [2. Printer gamma sensor adj.]I shows error 31Program has been used2. "36 mode menu screen"Press the [1. Process adjustment] key.3. "Process adjustment menu screen"Press the [2. Drum peculiarity adjustment] key.4. "Drum peculiarity adjustment menu screen"Press the [3. Automatic gamma adjustment]I shows error code 29-07 Note Has been replaced by the developerI'm very tired of this holidays Please help

mdar
10-14-2013, 11:11 AM
Has been replaced by the yellow developing unit and Clean the gamma sensor in the colour registration unit But the problem persists

mdar
10-14-2013, 11:19 AM
I'm very tired of this device
It is the second I have the same problem in the two devices
Is it possible to have a role in this heat problem

Note that the device used before entering into Iraq
Because in Iraq No new devices

Custom Search