PDA

View Full Version : Jamming Konica minolta c500 bypass mishandled paper J10-11


Custom Search


vangraph
08-14-2012, 03:58 PM
Hi All, Hope anyone can help me with this? I have a konica minolta c500 and was running a job through bypass. All of a sudden it is saying there is a jam/mishandled paper at the bypass tray. It ask me to take out paper and place it back on. I tried that, but it won't continue pass the image showing the jam? I tried restarting, tried reset page count. I even took it apart and reseat all connections. ThanksGary

jsol68
08-14-2012, 04:15 PM
Hi All, Hope anyone can help me with this? I have a konica minolta c500 and was running a job through bypass. All of a sudden it is saying there is a jam at the bypass tray. It ask me to take out paper and place it back on. I tried that, but it won't continue pass the image showing the jam? I tried restarting, tried reset page count. I even took it apart and reseat all connections. ThanksGary J10-03 while trying to feed from the bypass tray. Solution: CAUSE: The Tray up drive motor (M35) for the bypass unit has failed. SOLUTION: Replace the Tray up drive motor (p/n 13HA80021).

vangraph
08-14-2012, 04:22 PM
J10-03 while trying to feed from the bypass tray. Solution: CAUSE: The Tray up drive motor (M35) for the bypass unit has failed. SOLUTION: Replace the Tray up drive motor (p/n 13HA80021).Thanks!gary

JustManuals
08-14-2012, 04:39 PM
This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from


http://www.justmanuals.com (http://www.justmanuals.com)


Paul@justmanuals.com (Paul@justmanuals.com)

vangraph
08-14-2012, 04:42 PM
This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from http://www.justmanuals.com (http://www.justmanuals.com)Paul@justmanuals.com (Paul@justmanuals.com)Thanks for the offer, I already have the manuals.

vangraph
08-14-2012, 04:44 PM
J10-03 while trying to feed from the bypass tray. Solution: CAUSE: The Tray up drive motor (M35) for the bypass unit has failed. SOLUTION: Replace the Tray up drive motor (p/n 13HA80021).Hi, I replaced it, but still didn't work. Anything else you think would cause this?Gary

jsol68
08-14-2012, 05:25 PM
When paper is placed in the Manual paper feed tray, the tray does not lift and this creates a misfeed condition. This could be due to a poor wiring connection or a failed ADU driver control board. SOLUTION: Check the Upper limit sensor and if it checks OK in the IO mode, then confirm 24V DC at the pins of connectors 539-B10-1 and 539-B11. If the voltage drops significantly, this could be an indication of a failed Conveyance Driving Board (p/n 65AA -905 2E). Note: Make sure the harness for the Manual feed tray is not pinched or damaged.

vangraph
08-14-2012, 08:47 PM
When paper is placed in the Manual paper feed tray, the tray does not lift and this creates a misfeed condition. This could be due to a poor wiring connection or a failed ADU driver control board. SOLUTION: Check the Upper limit sensor and if it checks OK in the IO mode, then confirm 24V DC at the pins of connectors 539-B10-1 and 539-B11. If the voltage drops significantly, this could be an indication of a failed Conveyance Driving Board (p/n 65AA -905 2E). Note: Make sure the harness for the Manual feed tray is not pinched or damaged.


Thanks again!


Gary

Custom Search