PDA

View Full Version : Jamming DF-621 jamming bizhub 363


Custom Search


jujitsu47
06-12-2014, 02:51 PM
Jamming alot on 2nd page and others. i have replaced the feed roller and seperation roller assy. Happens most on scanning feed, but does also on regular copy feed originals. adjusted adf registraton feed loop and it did help the regular feed originals but not the scanning. any help is appreciated...

Kidaver
06-12-2014, 03:02 PM
There is a tech bulletin about adjusting the reading motor tension, adding some spacing washers, changing the flag sensor, changing the front and back lever assemblies, and changing the gear assembly. I've been fighting this issue for about a year seeing it mostly with customers with high scanning volume. I've recently did the levers and spacers for a customer and need to check on them to see if it's finally resolved this issue.

CompyTech
06-12-2014, 03:06 PM
Replace the front and rear lever assys.. They changed the design of them recently, and we had a couple jamming and we replaced them, and that seemed to do the trick.

Here's the part numbers for the updated parts: (A143PP9P01 Lever Assy (Front) ) & (A143PP9Q01 Lever Assy (Rear) )

jujitsu47
06-12-2014, 04:09 PM
i ordered the levers, will update ya all when arrive and install.....tks

blackcat4866
06-13-2014, 03:01 AM
Jam codes? =^..^=

JR2ALTA
06-13-2014, 04:02 AM
A common jam, (cost-free!), on these models is the angled sensor on the top cover of the adf. It's easy to overlook but is very prone to paper dust, I promise it's a legit fix for registration jams. Just clean it.

jujitsu47
06-13-2014, 04:38 PM
Jam codes? =^..^=

yup, waiting on parts....backordered... i had jam codes, but left on table. good point though....lol

Kidaver
06-13-2014, 05:10 PM
yeah seems the levers are in demand lol I ordered some and it took about a week longer for them to come in. The jam codes you normally see are 66-02. Tech bulletin TAUS1200978EN has all the info....it's been revised 4 times so far...

Cookr
03-14-2017, 03:56 PM
Can anyone give me a copy of this bulletin TAUS1200978EN I cant seem to find it. Thanks

CompyTech
03-14-2017, 05:44 PM
Can anyone give me a copy of this bulletin TAUS1200978EN I cant seem to find it. Thanks

Appears since KMBS has updated their knowledge base, that TAUS1200978EN is no more and has been replaced by this KBA01200978.

allan
03-14-2017, 08:22 PM
A common jam, (cost-free!), on these models is the angled sensor on the top cover of the adf. It's easy to overlook but is very prone to paper dust, I promise it's a legit fix for registration jams. Just clean it.

Jip...
The square hole for the reflective sensor black out gets paper fragments in there.

Cookr
03-14-2017, 10:10 PM
Appears since KMBS has updated their knowledge base, that TAUS1200978EN is no more and has been replaced by this KBA01200978.

Hmm when I search for that one under the bulletins I don't see it either?

CraigW
03-15-2017, 06:24 PM
Neither bulletin #s can be found.

To me...... the paper present actuator with the added magnet is one of the best resolves for 66-02.

Only occurs when utilizing the 70 OPM option during scanning.

blackcat4866
03-16-2017, 01:21 AM
Jip...
The square hole for the reflective sensor black out gets paper fragments in there.

I believe that one is 66-05, but we still don't know what code the poster is getting. =^..^=

Cookr
03-16-2017, 03:00 PM
Neither bulletin #s can be found.

To me...... the paper present actuator with the added magnet is one of the best resolves for 66-02.

Only occurs when utilizing the 70 OPM option during scanning.

Happen to have the part number for that? Thanks

CraigW
03-16-2017, 04:17 PM
Actuator = A3CFPP4VOO

Magnet = A3CFPP1700

Don N.
05-02-2017, 09:13 PM
Actuator = A3CFPP4VOO

Magnet = A3CFPP1700

See my post on 66-02 jams for this feeder. The left cover (lid) is warping upward. When it reaches about 25mm or more from the original table to the underside of the cover, the paper empty flag is too high and the angled area no longer hits the feed tires shaft at it's bent spot. This makes it bounce and read another false page, then tried to feed against the black felt friction pads. Our shop fix is applying about 39 lbs of weight to the feeder lid for a week or two, then put it out in the field. So far they have not warped back up. Any lid 23~24mm is fine. 25+ you will get 66-02 jams after last page is fed.
Prove it by simply pressing down with medium pressure on the cover. It won't fail! I posted slo no video proving this fix. The magnet in the actuator is just a band aid.

Custom Search