Results 1 to 10 of 10
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Oct 2012
    Location
    Belize
    Posts
    147
    Rep Power
    25

    IRA4225 Error code E000014-002 displayed

    I have replaced the fuser film, presssure roller and bearings and error occurs occasionally. I have tested fuser motor and it works properly. Any advice and next step.
    Thanks

  2. #2
    Service Manager 10,000+ Posts
    IRA4225 Error code E000014-002 displayed

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: IRA4225 Error code E000014-002 displayed

    Quote Originally Posted by ldfrepairs View Post
    I have replaced the fuser film, presssure roller and bearings and error occurs occasionally. I have tested fuser motor and it works properly. Any advice and next step.
    Thanks

    COPIER>FUNCTION>FIXING
    NIP-CHK Check of fixing nip width.

    Use case - When replacing the fixing-related parts (fixing Roller, Pressure Roller)
    - When a fixing failure occurs
    Adj/set/operate method
    1) Print approx. 20 sheets of A4 size paper.
    2) Make a solid black print (setting value: 7) with COPIER> TEST>PG> TYPE.
    3) Set the output of step 2 on the Multi-purpose Tray while placing the printed side down.4) Perform the size setting of the Multipurpose
    Tray.
    5) Select the item, and then press OK key.A sheet is stopped once in a state held by the Fixing Nip area, and is delivered
    approx. 20 seconds later.
    6) Measure the nip width of delivered sheet.

    It is judged as normal: (iR-ADV 4251: 8.1 to 10.1 mm, iR-ADV 4245/4235/4225 :7.5 to 9.5 mm) at the center, and difference
    between front and rear is within 1.0 mm. If there is an error, execute step 6.

    7) Check the Fixing Roller, Pressure Roller, and Fixing Lower Unit,
    and replace damaged part.
    Related service mode COPIER> TEST> PG> TYPE



    did u have a CQ issue before code

    >try this --remove drum n' dev unit and inspect the HV connections > now re-seat drum and dev unit.



    1. Check connection of the Connector (J2001/J203).
    2. Replace the Fixing Motor (M2).
    3. Replace the DC Controller PCB (UN2).

    how stable is your Supply Voltage from outlet
    especially Neutral to Ground - should be 0v +/- 0.5v at all times
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Senior Tech 100+ Posts
    Join Date
    Oct 2012
    Location
    Belize
    Posts
    147
    Rep Power
    25

    Re: IRA4225 Error code E000014-002 displayed

    Thanks will perform nip width test

  4. #4
    Senior Tech 100+ Posts
    Join Date
    Oct 2012
    Location
    Belize
    Posts
    147
    Rep Power
    25

    Re: IRA4225 Error code E000014-002 displayed

    I eventually got to replace the complete fixing assembly. check nip width but still getting the Error code 000014 displayed. Any other suggestion would be greatly appreciated.

  5. #5
    Service Manager 10,000+ Posts
    IRA4225 Error code E000014-002 displayed

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: IRA4225 Error code E000014-002 displayed

    Quote Originally Posted by ldfrepairs View Post
    I eventually got to replace the complete fixing assembly. check nip width but still getting the Error code 000014 displayed. Any other suggestion would be greatly appreciated.

    clear code ?
    Fixing Drive Unit ??


    Inspect the HV connections


    any other errors ?

    =========================================
    point to note


    Part number FM4-7897-000 goes to the higher speed models, imageRUNNER ADVANCE 4051/4251, and the color of the film is an off white color. Check the image below.




    Part number FM4-7900-000 goes to the lower speed models, imageRUNNER ADVANCE 4025/4035/4045/4225/4235/4245, and the color of the film is black in color. Check the image below.

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #6
    Senior Tech 100+ Posts
    Join Date
    Oct 2012
    Location
    Belize
    Posts
    147
    Rep Power
    25

    Re: IRA4225 Error code E000014-002 displayed

    The Unit I replaced is the FM4-7900.
    Next step i guess will be to check the HV connections again and then replace the Fixing drive unit.

  7. #7
    Service Manager 10,000+ Posts
    IRA4225 Error code E000014-002 displayed

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    22,606
    Rep Power
    658

    Re: IRA4225 Error code E000014-002 displayed

    Quote Originally Posted by ldfrepairs View Post
    The Unit I replaced is the FM4-7900.
    Next step i guess will be to check the HV connections again and then replace the Fixing drive unit.
    Tekcat asked if you CLEARED the error!?

  8. #8
    Senior Tech 100+ Posts
    Join Date
    Oct 2012
    Location
    Belize
    Posts
    147
    Rep Power
    25

    Re: IRA4225 Error code E000014-002 displayed

    Yes I did

  9. #9
    Engineer senior 100+ Posts giogi's Avatar
    Join Date
    Jan 2016
    Location
    Italy
    Posts
    180
    Rep Power
    25

    Re: IRA4225 Error code E000014-002 displayed

    Check or replace the FM4-9179-000 MAIN DRIVE ASSEMBLY
    "Knowledge is a source, but unfortunately ignorance is a sea."

  10. #10
    Senior Tech 100+ Posts
    Join Date
    Oct 2012
    Location
    Belize
    Posts
    147
    Rep Power
    25

    Re: IRA4225 Error code E000014-002 displayed

    The main drive assembly is what I am looking at now. have requested a quotation to purchase

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here