Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Dec 2012
    Location
    willemstad
    Posts
    119
    Rep Power
    24

    Canon C750 press E004-0101

    Hello,
    anyone had this error on a imagepress C750 before E004-0101 ?

    take out fixing unit and inspect heater lamp, and connections everything looks ok, did not find any shorted wires.

    As soon i put the unit back in and a few prints later error shows back again.

    Anny ideas apreciated,

    Antonio

  2. #2
    Senior Tech 100+ Posts
    Join Date
    Dec 2012
    Location
    willemstad
    Posts
    119
    Rep Power
    24

    Re: Canon C750 press E004-0101 Problem solved

    machine was plugged to a 120 VAC outlet

    Plugged machine to dedicated 220 VAC , but left finisher and paper deck to the 120 VAC outlet

    Works ok now

  3. #3
    Technical/IT Support 500+ Posts Venom's Avatar
    Join Date
    Nov 2009
    Location
    Ontario
    Posts
    764
    Rep Power
    40

    Re: Canon C750 press E004-0101

    Different plugs, someone getting creative with a cheater box?
    IBM, Mita, Konica Minolta, Ricoh, Kyocera, HyPAS, Canon, Oce, Samsung, HP, TEO IP PBX/Unified Communications, Comptia Network+ Comptia PDI+ Certifications

  4. #4
    Technician
    Join Date
    Oct 2023
    Location
    Ikeja
    Posts
    19
    Rep Power
    1

    Re: Canon C750 press E004-0101

    Quote Originally Posted by jose antonio View Post
    Hello,
    anyone had this error on a imagepress C750 before E004-0101 ?

    take out fixing unit and inspect heater lamp, and connections everything looks ok, did not find any shorted wires.

    As soon i put the unit back in and a few prints later error shows back again.

    Anny ideas apreciated,

    Antonio
    Hi,


    [Detail]

    The lower belt assembly (FM1-C722-000) with insufficient amount of grease applied to its gear may have been distributed in the field due to the poor control of the amount of applied grease.
    When an amount of grease applied is insufficient, gears may wear out, and additionally, the bearing may be displaced tocause the following symptoms.


    <When a gear is worn out>
    - E007-0022 : Pressure Belt full displacement error


    <When a bearing is displaced>
    - E004-0101 : Protection circuit error
    - E002-0101 : Pressure Belt temperature increase detection error


    For above reason, amount of grease applied at the gears may need to be checked when replacing the lower beltassembly (FM1-C722-000).

    [Service work]

    When replacing the lower belt assembly (FM1-C722-000), check the amount of applied grease and apply the grease by following the procedures below:
    1) Check whether the proper amount of grease is applied to the gear of the lower belt assembly (FM1-C722-000).
    [A] shows the state where insufficient grease is applied, and [B] shows the state where proper amount of grease is applied.
    If the amount of grease is insufficient, go to the step 2). If the proper amount of grease is applied, carry on replacement.



    [Reference]
    The part serial number [a] is stated on the label attached to the front side of the lower belt assembly (FM1-C722-000).
    The lower belt assembly (FM1-C722-000) with the part serial number 3S00016789 or later have the proper amount of grease applied to its gear.



    - If one of the target machines in the following list had no history of lower belt assembly replacement, the greaseamount may be insufficient so please apply the grease.
    L/60 Series are target machines. Be sure to apply grease.

    2) Prepare SE1107 grease lube (FY9-6036), and apply the proper amount of grease to the gear of the lower belt assembly (FM1-C722-000).
    Apply the grease to the whole circumference of the gear by rotating the gear with a hand.
    After applying the grease, carry on replacement.
    [Reference] When replacing the upper belt assembly (FM1-C721-000), be sure to apply the proper amount of grease to the gear of the lower belt assembly as stated in Service Manual.



    [Service parts]
    FY9-6036 LUBE, SE1107 GREASE


    3. Or Try to replace the small fuse pcb on upper fixing belt

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here