Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 6 of 6
  1. #1
    Technician
    Join Date
    Oct 2009
    Location
    Wroclaw
    Posts
    27
    Rep Power
    22

    IRADV 8095 E 302-001

    Hi all,
    I have a problem with the photocopier iradv 8095 with error E302-0001. are the connections to reader controller ok.Copy of glass is ok.
    Copying from the document feeder causes an error .

    any ideas

  2. #2
    Service Manager 1,000+ Posts vigour's Avatar
    Join Date
    Aug 2010
    Posts
    1,033
    Rep Power
    35

    Re: IRADV 8095 E 302-001

    E302-0001 refers to Front side scanning
    I think there is a break in your flex cable which shows up when scanner reaches the slide read position
    Go Level 2> Function> System> RCON Backup,
    Make P Print
    Do RCON clear
    Level 2 Function> System > RCON Restore
    Not all values are restored so:
    Input RCon values. from P PRINT

    If the problem persists:
    1 reseat flex cable from Reader Controller to Scanner unit in the READER
    2 One of these has a problem ( Reader Controller, Scanner Unit, or Flex Cable) ALL in The READER

    E302-0101 refers to the same parts in DF (backside scanner)


    http://www.copytechnet.com/forums/canon/69065-ir-adv-6065-code-error-e302-0101-a.html


  3. #3
    Technician
    Join Date
    Aug 2017
    Posts
    13
    Rep Power
    6

    Re: IRADV 8095 E 302-001

    Quote Originally Posted by vigour View Post
    E302-0001 refers to Front side scanning
    I think there is a break in your flex cable which shows up when scanner reaches the slide read position
    Go Level 2> Function> System> RCON Backup,
    Make P Print
    Do RCON clear
    Level 2 Function> System > RCON Restore
    Not all values are restored so:
    Input RCon values. from P PRINT

    If the problem persists:
    1 reseat flex cable from Reader Controller to Scanner unit in the READER
    2 One of these has a problem ( Reader Controller, Scanner Unit, or Flex Cable) ALL in The READER

    E302-0101 refers to the same parts in DF (backside scanner)


    http://www.copytechnet.com/forums/canon/69065-ir-adv-6065-code-error-e302-0101-a.html


    Sir i got canon ir advance 6075 with same problem error 302-0001. i remove the whole assembly in DADF reader and clean but nothing happen. I reset the rcon but my problem is how to input manually the rcon values and how to go into level 2 service mode?
    Hopefully you can give a little advice.
    Thank you.

  4. #4
    Field Supervisor 500+ Posts dan7777's Avatar
    Join Date
    Dec 2012
    Location
    Bristol
    Posts
    681
    Rep Power
    27

    Re: IRADV 8095 E 302-001

    Quote Originally Posted by buboy2222 View Post
    Sir i got canon ir advance 6075 with same problem error 302-0001. i remove the whole assembly in DADF reader and clean but nothing happen. I reset the rcon but my problem is how to input manually the rcon values and how to go into level 2 service mode?
    Hopefully you can give a little advice.
    Thank you.
    When you lift the adf the cover in the back side behind the large glass you have to take off to take the connectors out has the factory settings under it. After you clean the glass in the scanner do a

    Level 1> Copier>Function>CCD

    DF-WLVL1=1 Ok
    DF-WLVL1=2 Ok
    DF-WLVL1=LNR=1 Ok

    DF-WLVL1=3 Ok
    DF-WLVL1=4 Ok
    BW-TGT




    I checked, the e302-0001 is for the scanner under the glass. There are other codes for codes of the scanner for back side in the adf. I don't clean that glass every call so it can get very dirty in a dirty environment. 30 years ago it was minimum call to clean scanner mirrors. For those settings clean white paper goes through the doc feeder and one setting on the glass. I put a piece of letter paper on the glass and one in the doc feeder and then run the settings.

  5. #5
    Junior Member
    Join Date
    Oct 2019
    Location
    San Cristobal
    Posts
    2
    Rep Power
    0

    Re: IRADV 8095 E 302-001

    Quote Originally Posted by dan7777 View Post
    When you lift the adf the cover in the back side behind the large glass you have to take off to take the connectors out has the factory settings under it. After you clean the glass in the scanner do a

    Level 1> Copier>Function>CCD

    DF-WLVL1=1 Ok
    DF-WLVL1=2 Ok
    DF-WLVL1=LNR=1 Ok

    DF-WLVL1=3 Ok
    DF-WLVL1=4 Ok
    BW-TGT




    I checked, the e302-0001 is for the scanner under the glass. There are other codes for codes of the scanner for back side in the adf. I don't clean that glass every call so it can get very dirty in a dirty environment. 30 years ago it was minimum call to clean scanner mirrors. For those settings clean white paper goes through the doc feeder and one setting on the glass. I put a piece of letter paper on the glass and one in the doc feeder and then run the settings.

    This is what I got:

    DF-WLVL1=1 Ok
    DF-WLVL1=2 NG!
    DF-WLVL1=LNR=1 Ok

    DF-WLVL1=3 Ok
    DF-WLVL1=4 NG!
    BW-TGT = OK

    What should I do?

    Thanks!

  6. #6
    Field Supervisor 500+ Posts dan7777's Avatar
    Join Date
    Dec 2012
    Location
    Bristol
    Posts
    681
    Rep Power
    27

    Re: IRADV 8095 E 302-001

    Quote Originally Posted by kiloa22 View Post
    This is what I got:

    DF-WLVL1=1 Ok
    DF-WLVL1=2 NG!
    DF-WLVL1=LNR=1 Ok

    DF-WLVL1=3 Ok
    DF-WLVL1=4 NG!
    BW-TGT = OK

    What should I do?

    Thanks!
    clean the mirror in the scanner. Replace scanner and/or cable. Has to be that or board.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here