iPF6300/6350/6300S/8300/8300S-Error Codes2618/2F44/2F48/2F49/2F50/2F51/2F52 (REVISED)

[teckat]

iPF6300/6350/6300S/8300/8300S

Error Codes 2618/2F44/2F48/2F49/2F50/2F51/2F52 (REVISED)

DETAILS:
Workflow procedure to resolve the error codes mentioned above:

NOTE: Remove and discard old print heads. DO NOT install new print heads at this time.

1. For the iPF8300 series, replace the carriage relay PCB for the above mentioned error codes.
If the iPF8300 is displaying a “can’t detect paper size” message, then the entire carriage assembly should be replaced.

2. For the iPF6300 series, replace the Main Controller PCB.
Service reminder: Boot printer up in Service Mode when replacing the Main Controller and follow board replacement steps (CPU). Then boot printer in Service Mode again to clear error. Simply entering Service Mode will automatically clear the error code.

3. * Boot printer in Download Mode and upgrade Firmware to the latest version.

4. Boot printer up normally and only put new PH’s in when the printer display indicates to do so.
Note:
A 2F52 error usually occurs when installing a carriage unit in the wrong model printer. However, in some cases, this error code can occur when a short circuit is detected between the Carriage Relay PCB/Main Controller PCB and the print head/s.
* Latest Firmware version as of this publication date:
iPF6300 : Ver.1.25
iPF6350 : Ver.1.25
iPF8300 : Ver.1.26
iPF6300S: Ver.1.08
iPF8300S: Ver.1.09

[kiwitech]

just for your info i had an 8300 that had some of those codes and tried all sorts tricks and replaced lots of bits working from the head back to the controller. the only thing that fixed it was replace the controller which also happened to be the easiest bit to change. in future i might start with the controller even though the workflow doesn't indicate that, making sure the heads are not an early batch that had problems.

[IkeW0491]

TY Tekcat,

I Copied and Pasted this into a Word Doc so I can have it for future reference.

IKE

[teckat]

TY Tekcat,

I Copied and Pasted this into a Word Doc so I can have it for future reference.

IKE

The Dude.jpgWELCOME----good luck

[seppoo]

Kiwitech
When you said controller , you mean Main controller or carriage relay??

/Seppo

[kiwitech]

I meant main controller ...accessed by removing panel at rear of printer.

[Aparsons]

I have an iPF 6300 that has the 03130031-2618 error and have so far replaced the power supply (I know, it is almost never the power supply - but I was a lot greener a week ago), the carriage PCB and the long cables (messy and tricky). Still the error persists unchanged. Even when I forgot to put the long timing strip back the error was the same.

This leaves the main controller board which at some £750 on the chance that it might be that I'm not about to do without a lot more diagnosis and research. Especially as the brains of the main controller are working - it's booting up, running the display, moving the carriage a couple of inches, giving the error message and also running the printer information menus. You cannot go into service mode, the S appears but everything stops (except printer information menus) when the 2618 error appears.

If I have access to another iPF 6300 can I use the main controller from that to diagnose mine?
There seems to be a bit of the 2618 about but have no accounts of it having been thoroughly diagnosed and solved. A few accounts on the net of people scrapping the printers in desparation.

[whole9]

Hello, I have an ipf8300s and my printer is giving the error 03130031-2f52. I have made a youtube video to show what this printer is doing:



I can't get into service mode and the carriage seems to be locked up or unable to move. However, the other day, the carrier was able to move and functioned properly. The error code still popped up. I've gotten many responses from techs that would have me replace a dozen parts just to make sure the problem is solved. With my budget, I'd like to narrow this down as far as possible before investing any more time and money into this repair.

I can't update the firmware without getting into print mode. Below you suggested replacing the carriage relay PCB. My printer was not saying, "can't detect paper size" though.

Thank you for your time.

iPF6300/6350/6300S/8300/8300S

Error Codes 2618/2F44/2F48/2F49/2F50/2F51/2F52 (REVISED)

DETAILS:
Workflow procedure to resolve the error codes mentioned above:

NOTE: Remove and discard old print heads. DO NOT install new print heads at this time.

1. For the iPF8300 series, replace the carriage relay PCB for the above mentioned error codes.
If the iPF8300 is displaying a “can’t detect paper size” message, then the entire carriage assembly should be replaced.

2. For the iPF6300 series, replace the Main Controller PCB.
Service reminder: Boot printer up in Service Mode when replacing the Main Controller and follow board replacement steps (CPU). Then boot printer in Service Mode again to clear error. Simply entering Service Mode will automatically clear the error code.

3. * Boot printer in Download Mode and upgrade Firmware to the latest version.

4. Boot printer up normally and only put new PH’s in when the printer display indicates to do so.
Note:
A 2F52 error usually occurs when installing a carriage unit in the wrong model printer. However, in some cases, this error code can occur when a short circuit is detected between the Carriage Relay PCB/Main Controller PCB and the print head/s.
* Latest Firmware version as of this publication date:
iPF6300 : Ver.1.25
iPF6350 : Ver.1.25
iPF8300 : Ver.1.26
iPF6300S: Ver.1.08
iPF8300S: Ver.1.09

[teckat]

looks like u have older Firmware v1.06_??? up to v1.11

Canon U.S.A. : Support & Drivers : imagePROGRAF iPF8300S

L Printer Tool
When a problem on the printer occurs and an error code is displayed, effectively disabling the printer, this service tool allows you to bypass the error and aid in troubleshooting. Under the above conditions the printer becomes disabled and cannot be flashed with firmware using the traditional methods. The L Printer
Tool allows you to “bypass” the error condition which allows you to update the printer with firmware. The L Printer Tool allows technicians to retrieve the Status Print and Print Inf. files electronically, providing information that may be necessary for troubleshooting purposes.

L_Printer_Tool_v 1.80_INSTRUCTIONS.pdf

L_Printer_Service_Tool_v1.80_32Bit.zip
L_Printer_Service_Tool_v1.80_64Bit.zip


================================================== ===========================

2F52 Error > August 28, 2011
Follow these instructions for the iPF8300/8300S series:
-Obtain NEW print heads
-Remove both old print heads.
-Replace the Carriage Relay PCB. (DO NOT PUT IN NEW PRINT HEADS YET)
-Boot printer in Service Mode allow printer to come to ready then turn OFF.
-Boot printer normally and wait for the printer to ask for the print heads then put the NEW print heads in.
-The printer will go through its normal ink cycle then will come to ready.

Error Codes 2618/2F44/2F48/2F49/2F50/2F51/2F52 (REVISED) 9-27-13
PROCEDURE FOR THE IPF8300 and IPF8300S;
Tech Tips:
To enter Service Mode; press LOAD & NAVIGATE while powering ON.
To enter Download Mode; press STOP & NAVIGATE while powering ON.

1. Remove side and top covers and defeat top cover interlock switch. This allows for examination of ink flow to print heads in step #7.
2. Turn printer ON in Download Mode and upgrade firmware.
3. Turn the printer OFF, remove both print heads and discard them away from the customer’s premises,
they MUST NOT be reused. DO NOT INSTALL NEW PRINT HEADS YET.
4. Replace the Carriage Relay PCB.
5. Turn the printer ON in Service Mode without the new print heads installed. When the display indicates ready, turn printer OFF. (Entering Service Mode will automatically clear any related
errors.)
6. Reboot the printer in user mode. When the carriage moves out to the center of the platen, Now install the new Print Heads and allow the printer to go through ink filling.
Observe and check that each ink line is being filled, else stop the printer and troubleshoot the inkflow problem with the syringe kit.
7. When printer is operational, re-install all covers and remove cover interlock switch cheats.
NOTE:
If the error code or error message still appears after this procedure has been followed, the Main Controller PCB should be replaced next.
• Turn off the printer when prompted and remove Print Heads.
• Turn the printer ON in Service Mode without the new print heads installed. When the display
indicates ready, turn printer OFF. (Entering Service Mode will automatically clear any related errors.)
• Reboot the printer in user mode. When the carriage moves out to the center of the platen, Now install the new Print Heads and allow the printer to go through ink filling.
• Check that the ink lines are being filled, else stop the printer and troubleshoot the ink-flow problem with the syringe kit.
• Check and ensure the firmware is at the latest version, if not, update it.
• When the printer is operational, re-install all covers and re-enable the top cover interlock switch.




1. For the iPF8300 series, replace the carriage relay PCB for the above mentioned error codes.

AND > If the iPF8300 is displaying a “can’t detect paper size” message, then the entire carriage assembly should be replaced.

u try the first (pcb)

maybe HYTEC can help with board repair

Factory Authorized Circuit Board Repair by Hytec Dealer Services, Inc.