Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Chooper74
    Guest

    Angry Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Hi Guys,

    I am a canon tech looking at an imageRUNNER Advance C5030i machine, the green light on the display panel is on, but machine is dead, their is no rotation or powering up, just a clicking noise from power supply area, when switched on. I have replaced the following parts:

    Main Controller 1
    Main Controller 2
    Hard Drive
    All Memory On Both Boards.

    Machine is still dead!

    Could it be a power supply issue?

  2. #2
    Service Manager 10,000+ Posts
    Canon imageRUNNER C5030 Dead/Only Green Power Light.

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,024
    Rep Power
    234

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Quote Originally Posted by Chooper74 View Post
    Hi Guys,

    I am a canon tech looking at an imageRUNNER Advance C5030i machine, the green light on the display panel is on, but machine is dead, their is no rotation or powering up, just a clicking noise from power supply area, when switched on. I have replaced the following parts:

    Main Controller 1
    Main Controller 2
    Hard Drive
    All Memory On Both Boards.

    Machine is still dead!

    Could it be a power supply issue?
    ---------------------------------------------------------------
    U mean the Green LED (Processing Data Light)

    Why would u change all those parts "without checking your supply voltage"


    Do you have AC voltage going into the AC driver and AC coming out
    if
    yes > now check your main switch assembly for any burn marks.

    You could Unplug connectors one at a time from the DC controller and power the machine on each time to see if it powers up, if it powers up during this test check the connector that leads to item causing short.(With the connector plugged back in , check the voltages on the pins
    for proper voltage.(need manual)

    But I would check procedure below first



    - First check for AC voltage going to the 12/24 Power Supply and ALL NIGHT PS (Power Supply) from AC DRIVER.


    AC voltage comes from the AC DRIVER at J1005 to J681 for the ALL NIGHT PS and also from the sub AC driver J1022 to J1101 of the 12V PS and J1102 of the 24V PS.

    Without AC power to the PCB's no DC voltage is outputted. Suspect the AC DRIVER PCB ASSEMBLY failed.
    AC Driver Part numbers-
    FM3-6052-000 iR-ADV C5035,5030 SERIES 120V
    FM3-6053-000 iR-ADV C5051,5045 SERIES 120V



    - Next -3V DC must output from the ALL NIGHT PS to the Relay PCB.


    ALL NIGHT PS J691 pins 2/3 (pink wires) to Relay PCB J413 pins 1/2.

    When the AC voltage is supplied to the ALL NIGHT PS and no 3V DC output replace the ALL NIGHT PS PCB ASSEMBLY - FK2-6324-000.

    - 3V DC flows from the ALL NIGHT PS to the Relay PCB and from the Relay PCB down to the 12 and 24 volt Power Supply.
    Check for 3volts at the RELAY PCB J411 pin 1 to J835 pin 1 to turn on the 12V PS and from the RELAY PCB J412 pin 1 to J834 pin 1 to turn on the 24V PS.

    No 3V DC from Relay PCB to J411/J412 pins 1, replace the RELAY BOARD ASSEMBLY FM3-7935-000

    Once the 3vdc voltage turns on the Power Supply, 12v is outputted from J835 to J411 Relay PCB (Orange wires) and 24V DC from J834 to J412 (Red wires).
    If there is no DC voltage outputted, replace POWER SUPPLY BOX ASSEMBLY FM3-6031-000.
    ---------------------------------------------------------------------------------------------------------------------------------------
    NOTE:The main power supply is referred to as the power supply box assembly in the parts catalog and the relay pcb is referred to as the relay board assembly in the parts catalog.
    Note: On this series the power plug should be disconnected before any boards or connectors are disconnected.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Technician
    Join Date
    Oct 2014
    Location
    london
    Posts
    13
    Rep Power
    12

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Quote Originally Posted by Chooper74 View Post
    Hi Guys,

    I am a canon tech looking at an imageRUNNER Advance C5030i machine, the green light on the display panel is on, but machine is dead, their is no rotation or powering up, just a clicking noise from power supply area, when switched on. I have replaced the following parts:

    Main Controller 1
    Main Controller 2
    Hard Drive
    All Memory On Both Boards.

    Machine is still dead!

    Could it be a power supply issue?
    try the drum driver pcb and make sure you get the connectors back into the correct ports.
    good luck

  4. #4
    Junior Member
    Join Date
    Jun 2020
    Location
    Tibro
    Posts
    7
    Rep Power
    0

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Hi.
    I have the same problem as the thread creator. Although my green lamp does not light, it only flashes once just when you turn on. Otherwise completely dead, just a very weak sound from AC power.
    I have replaced:
    AC driver pcb, All night PS and the Relay board. Still nothing ....


    Could it be the Power supply box?
    How do I move on?


    I bought this printer cheap because of this problem. So it would have been fun to be able to get it started and use it.


    Thanks in advance
    Mattias
    SWEDEN

  5. #5
    Junior Member
    Join Date
    Jun 2020
    Location
    Tibro
    Posts
    7
    Rep Power
    0

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Nobody?

  6. #6
    Service Manager 1,000+ Posts
    Canon imageRUNNER C5030 Dead/Only Green Power Light.

    skynet's Avatar
    Join Date
    Apr 2009
    Location
    England
    Posts
    1,519
    Rep Power
    68

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Test voltages do you have a service manual?
    When you think you have made a procedure idiot proof your company employs a better idiot.

  7. #7
    Service Manager 5,000+ Posts
    Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    8,293
    Rep Power
    178

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Quote Originally Posted by steeda View Post
    Nobody?
    thanks for reply to a dead thread..

    you didn't even state the: model.. all parts/errors

  8. #8
    Junior Member
    Join Date
    Jun 2020
    Location
    Tibro
    Posts
    7
    Rep Power
    0

    Re: Canon imageRUNNER C5030 Dead/Only Green Power Light.

    Quote Originally Posted by Phil B. View Post
    thanks for reply to a dead thread..

    you didn't even state the: model.. all parts/errors

    ...Ok, but as I wrote, I have the same issue as the thread maker, which means I have the same model, same problem. I listed which parts Ive changed, and if you read what he wrote in the beginning; his machine was completely dead, just like mine, because "I have the same problem as him" and therefore no "errors"

    But okay, I start a new thread.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here