Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Sep 2013
    Posts
    62
    Rep Power
    13

    Riso RZ990 Master Making Scanning/Writing

    Hello All,

    I recently got a used RZ990 which was having an issue burning masters at the full tabloid size (was only burning to about 10" wide)

    I checked the factory mode settings and reset them or their default values, which then made the images burn even smaller, image below:
    Screen Shot 2019-11-24 at 3.21.42 PM.jpg

    These are the settings I changed:
    Screen Shot 2019-11-24 at 3.21.55 PM.jpg

    Has anyone ever had an issue with this? Or have an image of how these values are set on their machine?

    Thanks,

    PJ

  2. #2
    Service Manager 5,000+ Posts
    Riso RZ990 Master Making Scanning/Writing

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    5,648
    Rep Power
    102

    Re: Riso RZ990 Master Making Scanning/Writing

    Quote Originally Posted by pj4nh View Post
    Hello All,

    I recently got a used RZ990 which was having an issue burning masters at the full tabloid size (was only burning to about 10" wide)

    I checked the factory mode settings and reset them or their default values, which then made the images burn even smaller, image below:
    Screen Shot 2019-11-24 at 3.21.42 PM.jpg

    These are the settings I changed:
    Screen Shot 2019-11-24 at 3.21.55 PM.jpg

    Has anyone ever had an issue with this? Or have an image of how these values are set on their machine?
    Thanks, PJ
    when you reset did you confirm it defaulted to the size you require? might have reset any copy/net settings also.

    why didn't you just reset borders?

    lemme guess you don't have a manual?

    if so did you follow all setup procedures after the main reset?

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Sep 2013
    Posts
    62
    Rep Power
    13

    Re: Riso RZ990 Master Making Scanning/Writing

    Quote Originally Posted by Phil B. View Post
    when you reset did you confirm it defaulted to the size you require? might have reset any copy/net settings also.

    why didn't you just reset borders?

    lemme guess you don't have a manual?

    if so did you follow all setup procedures after the main reset?

    Hello,

    I just reset those values to the scanner bed settings listed on the sticker adhered to the scanner unit (as referenced in the MZ7/9 Manual, having a friend send over the RZ9 tomorrow)

    I was unsure where to adjust the borders in the test mode settings, is there a place to do that in the master making section?

    Appreciate any advice.

    PJ

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Sep 2013
    Posts
    62
    Rep Power
    13

    Re: Riso RZ990 Master Making Scanning/Writing

    Quote Originally Posted by pj4nh View Post
    Hello,

    I just reset those values to the scanner bed settings listed on the sticker adhered to the scanner unit (as referenced in the MZ7/9 Manual, having a friend send over the RZ9 tomorrow)

    I was unsure where to adjust the borders in the test mode settings, is there a place to do that in the master making section?

    Appreciate any advice.

    PJ
    Hello,

    I was able to reconcile this issue via codes 540 and 541 the master front end and write start position codes. I set them to 80 and 0 respectively, however the images are still burning about 3/8" off center towards the bottom of the page (landscape).

    I'm curious if it's a clamp-range adjustment. Will give it a test now and report back.

    Thanks for any suggestions.

    PJ

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here