Results 1 to 5 of 5

Thread: CP 4024 59.F0

  1. #1
    Senior Tech
    CP 4024 59.F0

    Robinh's Avatar
    Join Date
    Dec 2009
    Location
    Bremerton
    Posts
    109
    Rep Power
    29

    CP 4024 59.F0

    I read a tip that this 59.F0 code on a CP 4025, was caused by a sticky solenoid in the fuser drive assy. I tore this baby down, and sure enough that foam was coming apart. Cleaned it all up, and I thought I successfully tested the drive clutch, but still getting the 59.F0 error. :-(

    My sensors are all working, it's just not driving the belt. I'm thinking I'm going to have to replace the fuser drive assy, but if anyone has any ideas, I'm all ears. I attached a pic of the solenoid

    Thanks

    Robin

    sorry for the typo in the title.
    Attached Images Attached Images

  2. #2
    Master Of The Obvious 10,000+ Posts
    CP 4024 59.F0

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    19,894
    Rep Power
    384

    Re: CP 4024 59.F0

    If the solenoid has magnetized it will have the same effect as the foam sticking. When I remove the foam, I replace it with a disk of control panel sticker or electrical tape, to prevent the metal actuator from contacting the core. You might try replacing the solenoid first. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  3. #3
    Senior Tech
    CP 4024 59.F0

    Robinh's Avatar
    Join Date
    Dec 2009
    Location
    Bremerton
    Posts
    109
    Rep Power
    29

    Re: CP 4024 59.F0

    Quote Originally Posted by blackcat4866 View Post
    If the solenoid has magnetized it will have the same effect as the foam sticking. When I remove the foam, I replace it with a disk of control panel sticker or electrical tape, to prevent the metal actuator from contacting the core. You might try replacing the solenoid first. =^..^=
    I've cleaned a ton of these solenoids on earlier models, and I can usually get them to stick outside the machine. This one wouldn't stick, I wasn't convinced the solenoid is causing the problem. But I've suffered from tunnel vision before, and will try your advice. I wonder if I can salvage a solenoid from a part machine?

    Thanks,

    Robin

  4. #4
    Senior Tech
    CP 4024 59.F0

    Robinh's Avatar
    Join Date
    Dec 2009
    Location
    Bremerton
    Posts
    109
    Rep Power
    29

    Re: CP 4024 59.F0

    Quote Originally Posted by blackcat4866 View Post
    If the solenoid has magnetized it will have the same effect as the foam sticking. When I remove the foam, I replace it with a disk of control panel sticker or electrical tape, to prevent the metal actuator from contacting the core. You might try replacing the solenoid first. =^..^=
    Blackcat4866, I wanted to follow up and let you know, I pulled the solenoid back out, took it apart and whacked the flapper to discharge any magnetism, then I applied a bit of thick duct tape, to replace the foam bit I cleaned off, and the 59.F0 code cleared. You're advice was dead on. Thank you.

    Robin

  5. #5
    Master Of The Obvious 10,000+ Posts
    CP 4024 59.F0

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    19,894
    Rep Power
    384

    Re: CP 4024 59.F0

    Congratulations on your success!

    I haven't whacked solenoid plunger on the concrete in ages! =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here