Results 1 to 7 of 7
  1. #1
    Junior Member venetech's Avatar
    Join Date
    Mar 2017
    Location
    Marcaibo
    Posts
    7
    Rep Power
    0

    Unhappy Konica Minolta Bhc 7000 stays warm and does not fail

    I have a Konica Minolta Bhc7000, the same gets ready, but when making several impressions gives the message "wait a little, the machine is heating up". And so it stays all the time and it does not give fault code, I'm a Venezuelan technician, thank you very much s help, Regards

  2. #2
    Junior Member
    Join Date
    May 2017
    Location
    Fairfield,NJ
    Posts
    2
    Rep Power
    0

    Re: Konica Minolta Bhc 7000 stays warm and does not fail

    most likey its the upper fuser lamp causing that problem. you might want to try to clean the thermistors also.

  3. #3
    Junior Member
    Join Date
    May 2017
    Location
    Southern California
    Posts
    4
    Rep Power
    0

    Re: Konica Minolta Bhc 7000 stays warm and does not fail

    You can probably do a couple of things.

    Try to remove all finishers and see if you get the same issue.
    Also try changing software sw settings in the service mode
    19-1 to 1
    19-2 to 1
    19-3 to 0

    Hope this helps, I had the same issues and this solved it on our end but there are many different "Please wait signs".

    Good luck

  4. #4
    Junior Member venetech's Avatar
    Join Date
    Mar 2017
    Location
    Marcaibo
    Posts
    7
    Rep Power
    0

    Re: Konica Minolta Bhc 7000 stays warm and does not fail

    Replace, fuser lamps, thermistors, fuser band, and still the fault

  5. #5
    Service Manager 2,500+ Posts
    Konica Minolta Bhc 7000 stays warm and does not fail

    Synthohol's Avatar
    Join Date
    Mar 2016
    Location
    north jersey
    Posts
    2,729
    Rep Power
    65

    Re: Konica Minolta Bhc 7000 stays warm and does not fail

    warm up is not just heat, its also self calibrating. clean your ITB/Reg sensors. make sure the belt isnt wrinkled or wavey.

  6. #6
    Technician
    Join Date
    May 2017
    Location
    Seoul
    Posts
    28
    Rep Power
    9

    Re: Konica Minolta Bhc 7000 stays warm and does not fail

    I had two cases.

    The warming up was continued on the C6501.
    It is under the fusing unit.
    65AA 5365 1 - FIXING LIMITER

    In the C7000, the PHOTO SENSOR was replaced at the bottom left of the fusing unit gear assembly.

    08AA 8551 2 PHOTO SENSOR
    A50U M555 00 PHOTO SENSOR

    You can order any of the sensors above and replace them.

  7. #7
    Junior Member venetech's Avatar
    Join Date
    Mar 2017
    Location
    Marcaibo
    Posts
    7
    Rep Power
    0

    Thumbs up Re: Konica Minolta Bhc 7000 stays warm and does not fail

    Ready, replace ps16 and limiter fixing, resolved the fault, many thanks, Regards

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here