Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Technician
    Join Date
    Mar 2016
    Location
    Saint Denis
    Posts
    24
    Rep Power
    8

    bizhub C224e Magenta on border of prints

    Hello

    I am having an issue with a bizhub C224e. It magenta on the border of prints. i did the following :

    1. Replaced the 4 drum units and also the transfer belt

    2. Did image + stabilization

    3. No P codes in normal or service mode

    4. Cleaned the laser unit and also the eraser lamps

    5. Cleaned registration sensors

    6. Verified after a print in colour, no ink accumulated on the drums but ink accumulated on transfer belt : see image at below link
    Dropbox - picture.jpg

    7. Verified after a print in Black, no ink accumulated on the drums and no ink accumulated on transfer belt

    I am stuck at this point, please share any tips that might help me out of this problem.

    Thanks

  2. #2
    Senior Tech 250+ Posts
    Join Date
    Dec 2009
    Posts
    301
    Rep Power
    28

    Re: bizhub C224e Magenta on border of prints

    Original drum units or rebuild?
    Did you check developing units?
    I have seen rebuilded drum acting like this few times if charge coronas is not fit as it should and get closer to drum on one side.

  3. #3
    Field Supervisor 500+ Posts kingarthur's Avatar
    Join Date
    Feb 2008
    Posts
    773
    Rep Power
    36

    Re: bizhub C224e Magenta on border of prints

    post a pic of the actual image on the paper...you might have to adjust background voltages.....especially if using a non OEM drum
    Tip for the day; Treat every problem as your dog would.....If you cant eat it or f*ck it....then p*ss on it & walk away...

  4. #4
    Service Manager 1,000+ Posts
    bizhub C224e Magenta on border of prints


    Join Date
    Sep 2005
    Location
    South Jersey
    Posts
    2,053
    Rep Power
    70

    Re: bizhub C224e Magenta on border of prints

    If drums were all genuine K/M then sounds like you need a new Magenta Developer unit. I have had magenta on edges of page and it was because developer unit was crapping out. I first replaced drum and that didn't work. When I checked dev unit most of the developer was gone.

  5. #5
    Technician
    Join Date
    Mar 2016
    Location
    Saint Denis
    Posts
    24
    Rep Power
    8

    Re: bizhub C224e Magenta on border of prints

    Hello

    Thank you for replies.

    Its rebuild drum. I used them since a long time and it works. My boss no longer orders OEM. By the way if someone has a supplier for OEM please let me know. If they have a branch in south Africa will be better for shipping. Toxic can you please tell me how to check for the problem of charge coronas ?

    Yes i also checked the developing unit the layer of toner is uniform and the level 1 history is around 5-6 for all 4 developing units. Any other check ?


    Also one question :

    When doing the test pattern in service mode Graduation Adjust. When i select for example magenta :

    If the problem is with the Magenta drum or developing unit, will the problem appear on cyan and yellow ? I mean is it like only the Magenta section that gets to work ? or is it either black or 3 colour system ?

    I need this info for better understanding the machine.

    Thanks

  6. #6
    Service Manager 1,000+ Posts
    bizhub C224e Magenta on border of prints


    Join Date
    Sep 2005
    Location
    South Jersey
    Posts
    2,053
    Rep Power
    70

    Re: bizhub C224e Magenta on border of prints

    If it was doing it before "new" aftermarket drums, trans belt, etc than I still say you need new magenta developer unit even if it looks good. Of course you could always swap color drums around to see if problem follows drum.

    Very simple, overtoning on edges of page:

    1) Drum / corona grid

    2) Transfer belt or very rare transfer roller

    3) Developer unit

    These are only 3 things that will cause symptom you describe.

  7. #7
    Senior Tech 250+ Posts
    Join Date
    Mar 2009
    Posts
    282
    Rep Power
    27

    Re: bizhub C224e Magenta on border of prints

    These are only 3 things that will cause symptom you describe.[/QUOTE]

    You can swap the drum units & developer unit to confirm.
    What about toner? If that is also aftermarket, I guess anything can happen.
    Since toner contamination and dumping from front end, you need to check
    Hope this helps

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here