Page 1 of 3 123 LastLast
Results 1 to 10 of 26
  1. #1
    Technician
    Join Date
    Feb 2020
    Location
    Gaborone
    Posts
    13
    Rep Power
    1

    Angry Konica Minolta Bizhub 227 paper jam before fuser

    HI guys
    I have a bizhub 227 which jams paper before it enters fuser unit, actually the paper gets shrinked right under the fuser unit. Its coming up with error code 30:03 which points to exit sensor PS3, i changed all suggested components but still get jam at the same point. But if i remove image roller the paper goes through but without anything copied of course. Anyone with suggestions please help. My client is desparate.

    ....Khumz

  2. #2
    Field Supervisor 500+ Posts Bix's Avatar
    Join Date
    Apr 2018
    Location
    Berlin
    Posts
    783
    Rep Power
    14

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    Hi, so it's not easy to help you.
    1. What is the printer counter?
    2. What did you really replace?
    3. Have you replaced/cleaned the paper dust remover unit? At 150k the manual recommends replacement. There is an incredible amount of dirt that could dirty the 2nd transfer roller and therefore jams.

  3. #3
    Technician
    Join Date
    Feb 2020
    Location
    Gaborone
    Posts
    13
    Rep Power
    1

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    I did not check the counter but it should be more than 150k. The fuser unit and the image tranfare roller were changed. This machine could copy but failing on duplex. Before i could do anything i ran five none double sided copies and it was all good. I then attempted to run one double sided copy and it jammed the paper. I opened the side cover, removed jammed paper and from there on its jamming paper below fuser unit. It is clearly showing that the paper succesfuly pass through registration assembly and gets stuck below the fuser unit, as if the fuser unit is not turning or its totally closed.
    As i mentioned on my first post that if i remove image transfar roller the paper goes through without any problems at all but it will be blank of course.

  4. #4
    Technician
    Join Date
    Feb 2020
    Location
    Gaborone
    Posts
    13
    Rep Power
    1

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    Hi Bix

    Yes i did clean paper dust remover

  5. #5
    Service Manager 1,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    1,548
    Rep Power
    71

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    Did you try other paper tray and size?
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

  6. #6
    Technician
    Join Date
    Feb 2020
    Location
    Gaborone
    Posts
    13
    Rep Power
    1

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    Yes I did. Its same problem from all trays. Paper jams at the same point.

  7. #7
    Service Manager 1,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    1,548
    Rep Power
    71

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    There must be something out of place. Is the image registration ok when you pull jammed sheet?
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

  8. #8
    Technician
    Join Date
    Feb 2020
    Location
    Gaborone
    Posts
    13
    Rep Power
    1

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    The image registration is fine. The paper do not get stuck at all, the moment i open the machine the paper just falls out. The lead edge of the paper will be facing the entry into the fuser unit. The paper then multi- fold the whole A4 page kind of held against the drum.IMG_20200214_185716.jpg

  9. #9
    Service Manager 1,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    1,548
    Rep Power
    71

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    Check registration sensor and it's spring.
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

  10. #10
    Technician
    Join Date
    Feb 2020
    Location
    Gaborone
    Posts
    13
    Rep Power
    1

    Re: Konica Minolta Bizhub 227 paper jam before fuser

    I changed the sensor, will double check though

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here