Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Service Manager 2,500+ Posts
    C554e during firmware update MF controller shows N.G

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    4,206
    Rep Power
    82

    C554e during firmware update MF controller shows N.G

    Here we have a classic case of machine just had a simple DF jamming issue stripped & cleaned all sensors full of hole punches etc test feed DF fine.

    So I see the machine has never had the firmware updated so while I was finishing my coffee stuck in my pre Prepared USB stick that ive used the day before no problem.

    First I updated the boot rom that passed OK then chose the start the main fw update.

    So at the end of the update process the DF, finisher, printer etc all checksum update ok but the MF Controller shows N.G.

    Restarting the Machine with the USB in same thing happens. I downloaded a fresh fw copy on another USB still says controller N.G.

    Restarting the machine without the USB pen in the machine won’t boot sits & two ‘shark fins’

    Now i’m at a loss. Any ideas!?

    Classic case of “if it ain't broke don’t try to fix it.”
    Attached Images Attached Images
    Let us eat, drink, and be merry, because tomorrow we may die!

    www.copierfirmware.co.uk

  2. #2
    Field Supervisor 500+ Posts
    Join Date
    Sep 2008
    Location
    Flat Rock Michigan
    Posts
    763
    Rep Power
    32

    Re: C554e during firmware update MF controller shows N.G

    Quote Originally Posted by copier tech View Post
    Here we have a classic case of machine just had a simple DF jamming issue stripped & cleaned all sensors full of hole punches etc test feed DF fine.

    So I see the machine has never had the firmware updated so while I was finishing my coffee stuck in my pre Prepared USB stick that ive used the day before no problem.

    First I updated the boot rom that passed OK then chose the start the main fw update.

    So at the end of the update process the DF, finisher, printer etc all checksum update ok but the MF Controller shows N.G.

    Restarting the Machine with the USB in same thing happens. I downloaded a fresh fw copy on another USB still says controller N.G.

    Restarting the machine without the USB pen in the machine won’t boot sits & two ‘shark fins’

    Now i’m at a loss. Any ideas!?

    Classic case of “if it ain't broke don’t try to fix it.”
    disconnect hdd try again . if that fails reset mfp . check machine type and reflash.

  3. #3
    Senior Tech 250+ Posts
    Join Date
    Oct 2008
    Location
    Long Island, NY
    Posts
    305
    Rep Power
    0

    Re: C554e during firmware update MF controller shows N.G

    If all the other firmware except MFP downloads successfully, try doing just the MFP on its own. If it still doesn't work, try disconnecting options.

  4. #4
    Service Manager 2,500+ Posts
    C554e during firmware update MF controller shows N.G

    Synthohol's Avatar
    Join Date
    Mar 2016
    Location
    north jersey
    Posts
    2,645
    Rep Power
    63

    Re: C554e during firmware update MF controller shows N.G

    "MFP=NG" message
    Problem Solution
    ID: KBA01400074
    Related Products:bizhub C554e,bizhub 224e,bizhub 284e,bizhub 364e,bizhub 454e,bizhub 554e,bizhub 654e,bizhub 754e,bizhub C224e,bizhub C284e,bizhub C364e,bizhub C454e,bizhub C654e,bizhub C754e
    Related Options:


    Problem
    "MFP=NG" message may be indicated when attempting to install firmware.

    Solution
    CAUSE: Possible corruption of the SSD board (SSDB) or Hard Disk Drive (HDD) unit.

    SOLUTION: Before performing the steps below attempt to load firmware with the HDD physically disconnected from the MFPB. If the "MFP=NG" message returns then connect the HDD and proceed.

    Format the HDD/SSD Procedure:

    If able to access the Service Mode to format the HDD or SSD, perform the following steps.

    WARNING
    : Carefully follow the steps below, as doing so will avoid any unnecessary replacement components, such as the MFPB/PRCB/HDD (when only the SSD is actually required).

    1. Press Menu.
    2. Select Counter.
    3. Select Display Keypad.
    4. Access Service Mode "Stop 00" "Stop 01".
    5. Enter 9272 4 times (Factory default).
    6. Select System 2.
    7. Select HDD and set to "Uninstall".
    8. Select State Confirmation.
    9. Select Memory/HDD Adj.
    10. Press down-arrow 2/2.
    11. Select SSD Format.
    12. Select Logical Format.
    13. Power MFP OFF/ON.
    14. Repeat steps 1 through 5 to access Service Mode.
    15. Select System 1.
    16. Select Initialization.
    17. Clear All Data.
    18. Select System 2.
    19. Select HDD and set to "Install".
    20. Power MFP OFF/ON. \
    21. Repeat steps 1 through 5 to access Service Mode.
    22. Select State Confirmation.
    23. Select Memory/HDD Adj.
    24. Use the down-arrow to access page 2.
    25. Select HDD Format.
    26. Select Logical Format.
    27. Power MFP OFF/ON.
    • If the problem is not resolved after performing the above procedure, call the CSC for further support.
    • Please install the following "4e" Series firmware if the SSD has been approved for replacement and replaced. (Note: If firmware version is later than C8 then flash current firmware or update firmware to current base)

  5. #5
    Service Manager 2,500+ Posts
    C554e during firmware update MF controller shows N.G

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    4,206
    Rep Power
    82

    Re: C554e during firmware update MF controller shows N.G

    Thanks for the info.

    I'm going back with a new SSD will try the suggestions FW update with the HDD disconnected.

    It wont let me access CE mode so I have limited options.
    Let us eat, drink, and be merry, because tomorrow we may die!

    www.copierfirmware.co.uk

  6. #6
    Service Manager 1,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    2,084
    Rep Power
    92

    Re: C554e during firmware update MF controller shows N.G

    Quote Originally Posted by copier tech View Post

    It wont let me access CE mode so I have limited options.
    Have you tried access CE mode through reset thingy?
    Was about to post what Synthohol posted but feeling like Albonline knows more than KM tech support.
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

  7. #7
    Service Manager 2,500+ Posts
    C554e during firmware update MF controller shows N.G

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    4,206
    Rep Power
    82

    Re: C554e during firmware update MF controller shows N.G

    Quote Originally Posted by tsbservice View Post
    Have you tried access CE mode through reset thingy?
    Was about to post what Synthohol posted but feeling like Albonline knows more than KM tech support.
    "reset thingy?" you might need to be more specific?

    Let us eat, drink, and be merry, because tomorrow we may die!

    www.copierfirmware.co.uk

  8. #8
    Service Manager 1,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    2,084
    Rep Power
    92

    Re: C554e during firmware update MF controller shows N.G

    Quote Originally Posted by copier tech View Post
    "reset thingy?" you might need to be more specific?

    Not in public.
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

  9. #9
    Service Manager 2,500+ Posts
    C554e during firmware update MF controller shows N.G

    Synthohol's Avatar
    Join Date
    Mar 2016
    Location
    north jersey
    Posts
    2,645
    Rep Power
    63

    Re: C554e during firmware update MF controller shows N.G

    hey, i also thought about making sure the machine type is entered correctly.
    if you print the network config page does it show the correct model?

  10. #10
    Technician
    Join Date
    Jan 2020
    Location
    KENT
    Posts
    24
    Rep Power
    1

    Re: C554e during firmware update MF controller shows N.G

    Try down-grading the FW!

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here