Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16
  1. #11
    Master Of The Obvious 10,000+ Posts
    C1100 error C2236 and C2237.

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    18,448
    Rep Power
    318

    Re: C1100 error C2236 and C2237.

    Quote Originally Posted by allan View Post
    Jip there is a couple of hundred wires ends to test...
    It's easier if you've got somebody else to help you on the other side of the chassis.

    I'll usually use the tone function. I let the other person pick a connector and pin, then I'll find the match. If the tone is wobbly I'll switch to the lowest resistance setting for a better read. It just takes time and patience. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  2. #12
    RTFM!! 2,500+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    4,076
    Rep Power
    86

    Re: C1100 error C2236 and C2237.

    Quote Originally Posted by blackcat4866 View Post
    It's easier if you've got somebody else to help you on the other side of the chassis.

    I'll usually use the tone function. I let the other person pick a connector and pin, then I'll find the match. If the tone is wobbly I'll switch to the lowest resistance setting for a better read. It just takes time and patience. =^..^=

    Hey great thanks for that idea, used them while i was doing a bit of telecom's. Did not even cross my mind to use that.
    Used my scope in a useful manner on site the first time. Used it to verify if the stepper pulses and freq was ok, and it was not.

    What i want to do here is sit at the back of the machine where the PRCB needs to go and test from the connectors going to the PRCB to chassis ground.
    Whatever

  3. #13
    Senior Tech 250+ Posts
    C1100 error C2236 and C2237.

    tulintron's Avatar
    Join Date
    Jul 2014
    Location
    Belo Horizonte, Minas Gerais
    Posts
    323
    Rep Power
    17

    Re: C1100 error C2236 and C2237.

    Excellent reasoning. However, the analog multimeter better identifies the short circuit. In the case of the helper, it also helps a lot. But wires have connections to their full extent. These connections helped me to discard certain parts of the machine.
    Last edited by tulintron; 1 Week Ago at 05:53 PM.
    Nothing like day after day

  4. #14
    RTFM!! 2,500+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    4,076
    Rep Power
    86

    Re: C1100 error C2236 and C2237.

    So 2 hours of testing pins later I cleared the possibility of shorts and installed new board and did firmware.
    Any pin described as xSet would also go to ground like fSet tested as grounded.
    There is a loop wire in each unit that confirms if its installed or not that grounds it.
    In this case fSet was for fuser set and that being grounded would be normal if unit is installed.

    Machine came to ready. Jamming. Found bad ICP and connection on the CDB(ADUDB).
    Replaced ICP12 and jamming gone.

    Last the paper came out all wavey. Found one way bearing on deculer installed wrong way round and corrected that.

    Machine running.
    Whatever

  5. #15
    Master Of The Obvious 10,000+ Posts
    C1100 error C2236 and C2237.

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    18,448
    Rep Power
    318

    Re: C1100 error C2236 and C2237.

    Nice work! =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  6. #16
    Senior Tech 250+ Posts
    C1100 error C2236 and C2237.

    tulintron's Avatar
    Join Date
    Jul 2014
    Location
    Belo Horizonte, Minas Gerais
    Posts
    323
    Rep Power
    17

    Re: C1100 error C2236 and C2237.

    You have no posts with a sad ending. I already expected an answer like that, coming from you.
    Nothing like day after day

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here