Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Technician
    Join Date
    Oct 2019
    Location
    Manchester
    Posts
    23
    Rep Power
    9

    Konica c220 - Best way to change black dev clutch?

    I made a previous post about no black showing in prints and was informed that there's a good chance its the black dev clutch. I had a mess around trying to change it - Going through the back of the machine.

    I'm a fairly new apprentice so this aspect of the Konica's is a bit unfamiliar. What would be the easiest way to change the clutch?

  2. #2
    Service Manager 5,000+ Posts tsbservice's Avatar
    Join Date
    May 2007
    Posts
    7,103
    Rep Power
    346

    Re: Konica c220 - Best way to change black dev clutch?

    Ideally you will read manual
    Briefly:
    - remove some back covers
    - open PWB box
    - remove High voltage unit (HV)
    - remove the developing clutch/K cover
    - remove the developing clutch/K
    A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.

    Blessed are they who can laugh at themselves, for they shall never cease to be amused.

    I don't reply to private messages from end users.

  3. #3
    SanDiegoCopierRepair.com 1,000+ Posts
    Konica c220 - Best way to change black dev clutch?

    blazebusiness's Avatar
    Join Date
    Apr 2010
    Location
    From NY--- live in San Diego , Ca.
    Posts
    1,248
    Rep Power
    51

    Re: Konica c220 - Best way to change black dev clutch?

    Quote Originally Posted by tsbservice View Post
    Ideally you will read manual
    Briefly:
    - remove some back covers
    - open PWB box
    - remove High voltage unit (HV)
    - remove the developing clutch/K cover
    - remove the developing clutch/K
    What he sald. (in nice detail)

    The procedure he outlined for removing the C220 K dev clutch CL6 can be found in the Field Service Manual. So get a copy of that manual before you even attempt it.
    Anything can be made to work if you fiddle with it long enough- San Diego Copier Repair.com

  4. #4
    Service Manager 2,500+ Posts
    Konica c220 - Best way to change black dev clutch?


    Join Date
    Sep 2005
    Location
    South Jersey
    Posts
    3,836
    Rep Power
    133

    Re: Konica c220 - Best way to change black dev clutch?

    Quote Originally Posted by HarryBurgess View Post
    I made a previous post about no black showing in prints and was informed that there's a good chance its the black dev clutch. I had a mess around trying to change it - Going through the back of the machine.

    I'm a fairly new apprentice so this aspect of the Konica's is a bit unfamiliar. What would be the easiest way to change the clutch?
    Proceed with caution. A lot of things have to be removed to get to clutch. Even with a manual there is a good chance you will end up calling a technician anyway. And I know a lot of techs like myself who won't work on a machine taken apart by someone else.

    Do yourself a favor, and I mean no disrespect, but call a qualified technician and save yourself a lot of time and $$$$.

    Best of luck

  5. #5
    Service Manager 1,000+ Posts
    Konica c220 - Best way to change black dev clutch?


    Join Date
    Mar 2012
    Posts
    1,220
    Rep Power
    50

    Re: Konica c220 - Best way to change black dev clutch?

    Quote Originally Posted by copyman View Post
    Do yourself a favor, and I mean no disrespect, but call a qualified technician and save yourself a lot of time and $$$$.

    Best of luck
    Hrm... watch another more experienced tech do the job and take notes or to do it alone to earn your qualifications for yourself (or just fail). The question that is rarely questioned.

    Anyways, if you tackle this alone follow everyone's advice, bring your phone/camera and take lots of pictures prior to disassembly. Chances are if you were good with Legos as a kid, you can probably get all the pieces back together. Also, it is rare to burn a board out, but if you do not know how to prevent electrostatic discharge, now would be a good time to learn.

  6. #6
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Konica c220 - Best way to change black dev clutch?

    Be glad its not a C650 K drum encoder disk to be changed out.
    Whatever

  7. #7
    Certified Konica Expert 2,500+ Posts
    Konica c220 - Best way to change black dev clutch?

    Synthohol's Avatar
    Join Date
    Mar 2016
    Location
    North Jersey
    Posts
    4,943
    Rep Power
    216

    Re: Konica c220 - Best way to change black dev clutch?

    its a c220, it belongs at the bottom of the ocean where dinosaurs go to die.
    besides that, good luck. the whole machine is only worth 500.00 so dont put too many hours or money into it.
    i admire your bravery.

  8. #8
    Service Manager 1,000+ Posts femaster's Avatar
    Join Date
    May 2011
    Location
    A Small City in MI
    Posts
    1,264
    Rep Power
    97

    Re: Konica c220 - Best way to change black dev clutch?

    Personally, I'd want to make ABSOLUTELY SURE that the development unit ISN'T turning before I'd go through that much trouble.

    Not sure what has been done to this point, but I'd pull the dev unit first, make sure there is something on the mag roller for starters. If there is, I'd take a clean dry rag (or finger with a glove on) and push the developer and toner to the sides to make about a 1-inch wide blank area in the middle of the mag roller (spread what you moved out across the roller so that you don't have a big pile on the roller that might touch the drum). I'd then re-install the dev unit and the drum, power up the copier, let up come up to ready, print a meter page or something, then break it down again and check to see if that blank area was still on the mag roller. If it is, you know it's not turning and you can then look into the clutch. It the blank area is gone, then it's probably something else that is going on.

    That's just me though. I don't like to jump into lengthy and/or difficult situations unless I know for sure that's what I need to do.
    A Ricoh Service Tech for 7 year. A Konica Minolta Service Tech for 7 years. Now, KM service manager for 3 years.
    My Ricoh knowledge is slowly dwindling away at this point. Many things have been lost to time...

  9. #9
    Service Manager 1,000+ Posts femaster's Avatar
    Join Date
    May 2011
    Location
    A Small City in MI
    Posts
    1,264
    Rep Power
    97

    Re: Konica c220 - Best way to change black dev clutch?

    Quote Originally Posted by Synthohol View Post
    its a c220, it belongs at the bottom of the ocean where dinosaurs go to die.
    besides that, good luck. the whole machine is only worth 500.00 so dont put too many hours or money into it.
    i admire your bravery.
    Not the OP here, but I'd love to do just that at the place I work. Unfortunately, old units are their "cash cows". They love these machines where customers that have had the units long enough to where the maintenance contract costs have gone up. Those are their money winners.

    We have have tons of C220's and C360's out in the field. Hell we still have a few 7022's out there, at least one 501 that I can think of, still have one C420 (I think we finally got the last C351 swapped out, but I could be wrong), TONS of 250's and 350's a good number of 222's lots of 552's and C552's, still about five 600's and one 751. Probably over 50 from the 253/363 line...

    I could go on for days listing the antique crap I have to deal with on a daily basis!
    A Ricoh Service Tech for 7 year. A Konica Minolta Service Tech for 7 years. Now, KM service manager for 3 years.
    My Ricoh knowledge is slowly dwindling away at this point. Many things have been lost to time...

  10. #10
    Service Manager 2,500+ Posts
    Konica c220 - Best way to change black dev clutch?


    Join Date
    Sep 2005
    Location
    South Jersey
    Posts
    3,836
    Rep Power
    133

    Re: Konica c220 - Best way to change black dev clutch?

    Quote Originally Posted by femaster View Post
    Not the OP here, but I'd love to do just that at the place I work. Unfortunately, old units are their "cash cows". They love these machines where customers that have had the units long enough to where the maintenance contract costs have gone up. Those are their money winners.

    We have have tons of C220's and C360's out in the field. Hell we still have a few 7022's out there, at least one 501 that I can think of, still have one C420 (I think we finally got the last C351 swapped out, but I could be wrong), TONS of 250's and 350's a good number of 222's lots of 552's and C552's, still about five 600's and one 751. Probably over 50 from the 253/363 line...

    I could go on for days listing the antique crap I have to deal with on a daily basis!
    I would rather be working on some of those old models instead of a "few" new models I've seen.

    I see machines getting built with cheaper materials & parts which make less reliable.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here