Thanks Thanks:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Junior Member
    Join Date
    Sep 2020
    Location
    Lagos
    Posts
    8
    Rep Power
    0

    Bizhub c280 stopping inside the fusing unit

    Good day everyone. I have this c280 I'm maintaining for someone. The bypass roller doesn't pick up any paper but just roll over them. I inspected the separation roller packed it properly so to have proper contact, then it could pick paper but by aiding the paper into it. After some jobs, it started getting jammed at the fuser unit. I decided to use the tray to print, now they all get stuck at the fuser unit. I have followed everything i read here but still it persist. What can I do to as it is used for business.

  2. #2
    Field Supervisor 500+ Posts
    Bizhub c280 stopping inside the fusing unit

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    879
    Rep Power
    36

    Re: Bizhub c280 stopping inside the fusing unit

    Quote Originally Posted by Adeboy View Post
    Good day everyone. I have this c280 I'm maintaining for someone. The bypass roller doesn't pick up any paper but just roll over them. I inspected the separation roller packed it properly so to have proper contact, then it could pick paper but by aiding the paper into it. After some jobs, it started getting jammed at the fuser unit. I decided to use the tray to print, now they all get stuck at the fuser unit. I have followed everything i read here but still it persist. What can I do to as it is used for business.
    Replace all the feed rollers @ bypass.

    As far as the fuser jamming....is the paper folding up a bunch of times or is it straight? If it's folding up, sounds like the stripper pawls have toner build up or are corroded. How many pages on the fuser? If the paper is straight, you probably lost fuser rotation from a broken gear on the fuser or drive train.

  3. #3
    Junior Member
    Join Date
    Sep 2020
    Location
    Lagos
    Posts
    8
    Rep Power
    0

    Re: Bizhub c280 stopping inside the fusing unit

    The paper is straight and I have replaced the fuser but it is still the same. Sometimes it will stop at entry, but most times it is at the exit of the fuser. The error code is 3003.

  4. #4
    Field Supervisor 500+ Posts
    Bizhub c280 stopping inside the fusing unit

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    879
    Rep Power
    36

    Re: Bizhub c280 stopping inside the fusing unit

    Quote Originally Posted by Adeboy View Post
    The paper is straight and I have replaced the fuser but it is still the same. Sometimes it will stop at entry, but most times it is at the exit of the fuser. The error code is 3003.

    I'm not there and you haven't provided a lot of information.

    Have you checked the exist sensor @ fuser?

    You need to make sure you have constant drive @ fuser. I've seen cracked gears or gears with missing teeth cause the fuser to rotate at times but cause these types of problems.

  5. #5
    Junior Member
    Join Date
    Sep 2020
    Location
    Lagos
    Posts
    8
    Rep Power
    0

    Re: Bizhub c280 stopping inside the fusing unit

    Sorry to ask this bcos I seem confused now, how can I locate the fuser exit sensor. Is it the one on fuser or in the machine

  6. #6
    Field Supervisor 500+ Posts
    Bizhub c280 stopping inside the fusing unit

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    879
    Rep Power
    36

    Re: Bizhub c280 stopping inside the fusing unit

    Quote Originally Posted by Adeboy View Post
    Sorry to ask this bcos I seem confused now, how can I locate the fuser exit sensor. Is it the one on fuser or in the machine
    Sorry but you'll have to ask one of the resident experts on this machine. I'm just not familiar enough with the machine to say for sure. It's normally located on the fuser where the paper exists the unit.

  7. #7
    Junior Member
    Join Date
    Sep 2020
    Location
    Lagos
    Posts
    8
    Rep Power
    0

    Re: Bizhub c280 stopping inside the fusing unit

    Thanks for response, ve seen the sensor but it is not the problem, the shaft rotating the fuser get stucked at some point after picking up the paper but couldn't rotate it up hence it got jammed. But the shaft teeth are ok. What can I do

  8. #8
    Field Supervisor 500+ Posts
    Bizhub c280 stopping inside the fusing unit

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    879
    Rep Power
    36

    Re: Bizhub c280 stopping inside the fusing unit

    Quote Originally Posted by Adeboy View Post
    Thanks for response, ve seen the sensor but it is not the problem, the shaft rotating the fuser get stucked at some point after picking up the paper but couldn't rotate it up hence it got jammed. But the shaft teeth are ok. What can I do
    Not sure what shaft you're talking about that's getting stuck but that seems to be the source of your problem. I would recommend working backwards from the point where the fuser gear meshes up with the drive gear until you find the source of the binding. Sorry I can't be of more help.

  9. #9
    Junior Member
    Join Date
    Sep 2020
    Location
    Lagos
    Posts
    8
    Rep Power
    0

    Re: Bizhub c280 stopping inside the fusing unit

    I was able to get make the shaft roll, but it's now getting stuck at the exit tray

  10. #10
    Field Supervisor 500+ Posts
    Bizhub c280 stopping inside the fusing unit

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    879
    Rep Power
    36

    Re: Bizhub c280 stopping inside the fusing unit

    Quote Originally Posted by Adeboy View Post
    I was able to get make the shaft roll, but it's now getting stuck at the exit tray
    I assume you're talking about the internal tray and it has no finisher? If that's the case, is the paper coming all the way out or getting stuck before it completely exists the machine?

    I still suspect that you're losing drive at the fuser because the fuser is the last thing before the exit tray. It could be the sensor.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here