Dislikes: 0
Machine had a squeak, so I opened the right side jam door and cheated the door switch, ran a few on off cycles now the machine has a C2152 error. I have pulled out the transfer unit made sure sensors were clean, removed the fuser and reseated, reseated the transfer belt, but still have the code. What did I screw up? Any suggestions would be appreciated and thank you in advance.
Didn't have this one but may worth check this ICP:
IMG_7400.JPG
bizhub C224 has C2152 error code
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.
I don't reply to private messages from end users.
Have you opened and closed the front door with the power on to reset the code?
Only asking because you don’t mention it in your post.
Thank you for asking, tech51, that may have resolved the issue. I opened the door to turn the gear on the waste toner box, closed it and the code was gone. It had me going for a while, I pulled out the transfer multiple times, cleaned the ID sensors, pulled out the fuser unit, checked all the gears on the trans belt and fuser, etc. was ready to throw in the towel, checked the waste toner box, closed the front cover and it came to ready.Originally Posted by tech51
If it's not obvious...I am not a seasoned Konica tech, but I catch on real quick when pushed into the fire, I have made made note.
For future reference, you can get this code when toner blows up onto the inner frame, covering the sensor for the color primary transfer shift mechanism. This can occur at the same time as the primary transfer waste backing up. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
Thank you, blackcat. I did empty (Vacuum) the waste toner collector on the transfer belt unit when I had it out the fourth or fifth time and vacuumed the id sensors at the same time, so maybe that was an issue as well. It boils down to having done this for many of years, just not a lot of Konicas, and a little luck and some good help from Copytechnet.
The photo is too large to load, but the sensor is dead center in the middle of the rear transfer unit rail, and it doesn't look like a photointerrupter at all.
C2152 reduced.jpg
Ok, it's really small, but maybe you can see it. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
Thank you, I did take my vacuum and brush along that area you have mentioned as I am almost obsessive about having a clean contacts and sensors, so almost unknowingly, I am sure I vacuumed this area because I remember the sliding lever by it.
Being obsessive has it's benefits. I would know. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
I'd give you two thumbs up if I could.
Thanks: 
Likes: 
Reply With Quote
Bookmarks