Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21
  1. #11
    Senior Tech 100+ Posts
    Join Date
    Nov 2008
    Posts
    170
    Rep Power
    27

    Re: bizhub c300i jam tray 1

    Quote Originally Posted by allan View Post
    So you say it works just fine with another feeder unit?

    It seemed as though it did for a week or so, must have been a coincedence.

  2. #12
    Step aside, noob 1,000+ Posts EarthKmTech's Avatar
    Join Date
    May 2009
    Location
    Gigety
    Posts
    2,105
    Rep Power
    66

    Re: bizhub c300i jam tray 1

    make sure its not the cassette itself - i have seen straight out of the box from new damage to the very top edge of the mylar at the rhs of the cassette. Not even visible to the eye but can be felt by the finger nail, and sufficient enough to trap the top sheet feeding out the tray.

    I've also seen mylars installed crookedly by 1-2mm on the feed unit guides straight out of the factory causing jams too. (tray 2 jams)
    This account is no longer active and will no longer be used, I may re-join at a later date. Do not private message me, I will not get the notifications. Goodbye and all the best.

  3. #13
    Senior Tech 100+ Posts
    Join Date
    Nov 2008
    Posts
    170
    Rep Power
    27

    Re: bizhub c300i jam tray 1

    The problem was the fast clutch (cl10). It's behind the base board. Once replaced and tested it worked fine.

  4. #14
    Service Manager 1,000+ Posts
    bizhub c300i jam tray 1

    brent's Avatar
    Join Date
    Nov 2008
    Location
    Kellogg Idaho
    Posts
    1,007
    Rep Power
    36

    Re: bizhub c300i jam tray 1

    cantechman I see the clutch on the diagram and going to order it.. super fun to install? lol since I don't have another machine here in the office to try with
    until I get the part.. thank you very much for the link you guys are awesome
    brent

  5. #15
    Senior Tech 100+ Posts
    Join Date
    Nov 2008
    Posts
    170
    Rep Power
    27

    Re: bizhub c300i jam tray 1

    Quote Originally Posted by brent View Post
    cantechman I see the clutch on the diagram and going to order it.. super fun to install? lol since I don't have another machine here in the office to try with
    until I get the part.. thank you very much for the link you guys are awesome
    brent
    It wasn't that bad, the hardest part is just opening up the baseboard box, I'd say start to finish it took 45 min.

  6. #16
    Senior Tech 100+ Posts
    Join Date
    May 2018
    Location
    Hong Kong
    Posts
    162
    Rep Power
    8

    Re: bizhub c300i jam tray 1

    Quote Originally Posted by Cantechman View Post
    The problem was the fast clutch (cl10). It's behind the base board. Once replaced and tested it worked fine.
    I wanna ask, what's the function of this fast clutch?

  7. #17
    RTFM!! 2,500+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    4,460
    Rep Power
    100

    Re: bizhub c300i jam tray 1

    Quote Originally Posted by jwai View Post
    I wanna ask, what's the function of this fast clutch?
    I think its to clutch fast.
    Whatever

  8. #18
    Senior Tech 100+ Posts
    Join Date
    Nov 2008
    Posts
    170
    Rep Power
    27

    Re: bizhub c300i jam tray 1

    Quote Originally Posted by jwai View Post
    I wanna ask, what's the function of this fast clutch?

    I never really read what it's function is other then helping transport the paper but's only related to tray one and the bypass I do believe.

  9. #19
    Service Manager 1,000+ Posts
    bizhub c300i jam tray 1

    brent's Avatar
    Join Date
    Nov 2008
    Location
    Kellogg Idaho
    Posts
    1,007
    Rep Power
    36

    Re: bizhub c300i jam tray 1

    Quote Originally Posted by Cantechman View Post
    It wasn't that bad, the hardest part is just opening up the baseboard box, I'd say start to finish it took 45 min.

    I just received my clutches from km there probaly isnt a procedure in the book I assume? I wish I had another machine in the office to try on first so I don't look like a dork in the customer office.. lol I need to get it on the schedule and get it replaced.. you need to remove the base board is that right?

    thanks brent

  10. #20
    Service Manager 1,000+ Posts
    bizhub c300i jam tray 1

    brent's Avatar
    Join Date
    Nov 2008
    Location
    Kellogg Idaho
    Posts
    1,007
    Rep Power
    36

    Re: bizhub c300i jam tray 1

    looks not too bad. I hope to get to the customers office next week early.. I will advise.. it is in the manual as well as far as the clutch 10 I didnt see
    it before. but now I do. thanks all

    brent

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here