Results 1 to 4 of 4
  1. #1
    Junior Member
    Join Date
    Apr 2021
    Location
    Rovaniemi
    Posts
    3
    Rep Power
    0

    IC-417 boot errors, non functioning web UI, updates fail

    Hi,

    Konica Monilta C2070 and Fiery E300-04 IC-417.

    I managed to reinstall system software to IC-417 (replaced a dead HDD), but I'm getting following errors:

    Controller boots fine and ends to 00 state as it should.

    Printer controller menu only shows following error:
    "The request URL could not be retrieved."

    If connect I a monitor to monitor port the operating systems says following:
    "i2c-algo-ich: ICH_GPIO sendbytes: error - bailout
    kvf_driver_init: registered 18 device numbers
    i2c-algo-ich: ICH_GPIO sendbytes: error - bailout"

    I am able to connect ti IC-417 with Fiery Command Workstation, but I cannot access configuration because of non functioning web UI.

    Command Workstation reports updates available but I cannot install them because timeout to update server.

  2. #2
    Senior Tech 250+ Posts
    IC-417 boot errors, non functioning web UI, updates fail

    tulintron's Avatar
    Join Date
    Jul 2014
    Location
    Belo Horizonte, Minas Gerais
    Posts
    419
    Rep Power
    22

    Re: IC-417 boot errors, non functioning web UI, updates fail

    Quote Originally Posted by Faravid View Post
    Hi,

    Konica Monilta C2070 and Fiery E300-04 IC-417.

    I managed to reinstall system software to IC-417 (replaced a dead HDD), but I'm getting following errors:

    Controller boots fine and ends to 00 state as it should.

    Printer controller menu only shows following error:
    "The request URL could not be retrieved."

    If connect I a monitor to monitor port the operating systems says following:
    "i2c-algo-ich: ICH_GPIO sendbytes: error - bailout
    kvf_driver_init: registered 18 device numbers
    i2c-algo-ich: ICH_GPIO sendbytes: error - bailout"

    I am able to connect ti IC-417 with Fiery Command Workstation, but I cannot access configuration because of non functioning web UI.

    Command Workstation reports updates available but I cannot install them because timeout to update server.
    You can try to remotely access the IC desktop via Windows using the shortcut command MSTSC.
    Nothing like day after day

  3. #3
    Senior Tech 250+ Posts
    IC-417 boot errors, non functioning web UI, updates fail

    tulintron's Avatar
    Join Date
    Jul 2014
    Location
    Belo Horizonte, Minas Gerais
    Posts
    419
    Rep Power
    22

    Re: IC-417 boot errors, non functioning web UI, updates fail

    These errors are from Linux and show to be some bad contact on some hardware. Try to remove them all, clean the connections, connect them again and redo the installation of the system software.
    Nothing like day after day

  4. #4
    Junior Member
    Join Date
    Apr 2021
    Location
    Rovaniemi
    Posts
    3
    Rep Power
    0

    Re: IC-417 boot errors, non functioning web UI, updates fail

    Thanks, managed to get it working by removing all connectors, RAM, PCI-E expansion card and resetting them.
    After that ran a full reinstall.
    Now WebGUI works and updates download and install.

    However. Server is still saying "Product not enabled".
    Any idea why this happens?

    Konica C2070 is the printer.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here