Thanks: 
Likes: Trouble code 808 ..C 3102 ..updated firmware..replacement of fuser drive motor M3 and pressure release lever....also tried another fuser!
Sent from my SM-N981U using Tapatalk
Dislikes: 0
Trouble code 808 ..C 3102 ..updated firmware..replacement of fuser drive motor M3 and pressure release lever....also tried another fuser!
Sent from my SM-N981U using Tapatalk
i bet i know what it is!!
the belt fell off the duplex motor.
add a shim like i did to the lower corner.
[edit] i may be thinking of j3102, i dont remember now. dammit![/edit]
Last edited by Synthohol; 05-14-2021 at 03:43 AM.
We know a thing or two because we've seen a thing or two.
Also don't ask me for files without a contributor badge.
Originally Posted by antone
- Code: C3102
- Description:Heating roller failure to turn. During any state other than printing operation, the hard latch signal from one or both of the heating roller rotation latch detection 1 and the heating roller rotation latch detection 2 is turned ON.
- Causes:• Fusing unit • Fusing belt rotation sensor (PS56) (bizhub 958, bizhub PRO 958) • Heating roller rotation sensor (PS56) (bizhub 808/758) • Fusing motor (M30) • MFP board (MFPB)
- Remedy:1. Check the fusing unit for proper connection and correct as necessary. 2. Check the connector between M30-MFPB CN16E for proper connection and correct as necessary. 3. Check the connector of M30 for proper drive coupling and correct as necessary. 4. Check the fusing unit-relay CN260-MFPB CN30E for proper connection and correct or change as necessary. 5. PS56 I/O check, sensor check • Control signal: MFPB CN30E-14 (ON) • Location of electrical component: 9-C, 12-C 6. M30 operation check • Control signal: MFPB CN16E-4 (REM), MFPB CN16E-7 (LOCK) • Location of electrical component: 10-K 7. Replace M30. 8. Replace the fusing unit. 9. MFPB F2E or F14E conduction check 10. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958)
Let us eat, drink, and be merry, because tomorrow we may die!
For all your firmware & service manual needs please visit us at:
www.copierfirmware.co.uk - www.printerfirmware.co.uk
For me, its always been the eight pieces of paper accordianned in the fuser exit, that the enduser doesn't notice. It stops the fuser drive. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
Eight because it's 8 series or because it's bizhub 808
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.
I don't reply to private messages from end users.
A simple question, but it can solve:
Did you perform the trouble reset?
Nothing like day after day
Yes, exactly. =^..^=Eight because it's 8 series or because it's bizhub 808
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
Sounds like you've done all the logical steps----- If replacing the fuser unit and fuser motor and then running the trouble reset did not fix the issue, I would suspect something is bad in the fuser drive unit assembly.
Anything can be made to work if you fiddle with it long enough- San Diego Copier Repair.com
C 3102 not J 3102 ...fuser Lever under M30 no getting being pushed in from vertical transfer door!
Sent from my SM-N981U using Tapatalk
oh crap, i had that too, i added labels to the switch for thickness to get it to fully engage.
We know a thing or two because we've seen a thing or two.
Also don't ask me for files without a contributor badge.
Reply With Quote
Bookmarks