Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 23
  1. #11
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Konica Minolta C368 P-22

    Quote Originally Posted by Kenny View Post
    ive replaced the FRB and jigged the shutter issue still persists??
    It can go out of alignment ever so slightly it seems open but still not correct.
    You cab jig the door and the fuser and have a look if the patches are all there.
    Whatever

  2. #12
    Senior Tech 250+ Posts
    Konica Minolta C368 P-22

    Kenny's Avatar
    Join Date
    Jun 2009
    Location
    Leeds
    Posts
    455
    Rep Power
    37

    Re: Konica Minolta C368 P-22

    Quote Originally Posted by tsbservice View Post
    What happens if you run Stabilizer (Initialize + Image stabilization)?
    it then brings up a P-14 code

  3. #13
    Master Of The Obvious 10,000+ Posts
    Konica Minolta C368 P-22

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462

    Re: Konica Minolta C368 P-22

    Cyan developing isn't that great. Not sure if it will help. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  4. #14
    Senior Tech dantab1980's Avatar
    Join Date
    May 2015
    Location
    Coos Bay, Oregon
    Posts
    12
    Rep Power
    18

    Re: Konica Minolta C368 P-22

    Time to bring out the electrical diagram and trace the wiring to the issue. Might be a high/low voltage issue.

  5. #15
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,387
    Rep Power
    152

    Re: Konica Minolta C368 P-22

    Quote Originally Posted by dantab1980 View Post
    Time to bring out the electrical diagram and trace the wiring to the issue. Might be a high/low voltage issue.
    That is easy to see just check the IDC sensor values under state confirmation. I have had good values but the shutter did not not seem to close and that also gave P-codes.
    Whatever

  6. #16
    Field Supervisor 500+ Posts
    Join Date
    Jan 2009
    Location
    UK
    Posts
    826
    Rep Power
    50

    Re: Konica Minolta C368 P-22

    Quote Originally Posted by Kenny View Post
    it then brings up a P-14 code
    Well you seem to have done everything except replacing the ph unit. I’ve had these go faulty on this model a couple of times so might be worth trying that.

  7. #17
    Senior Tech 100+ Posts
    Konica Minolta C368 P-22


    Join Date
    Apr 2021
    Location
    Lake Tahoe, California
    Posts
    173
    Rep Power
    11

    Re: Konica Minolta C368 P-22

    Quote Originally Posted by tech51 View Post
    Well you seem to have done everything except replacing the ph unit. I’ve had these go faulty on this model a couple of times so might be worth trying that.
    Cheaper to replace the Belt and KDR first, everything is referenced off black.
    P codes were mentioned but was there an actual color registration issue? P22s and color reg for me has always been the belt, but I've always replaced the KDR anyway just to avoid the callback. Almost every time these have been well under life.

    And if you're running into color reg issues they tend to be temporarily fixed by stabilizing. IE Stabilize and it looks great, but slowly drifts over 500 pages then looks good again after it stabilizes.

  8. #18
    Senior Tech 250+ Posts
    Join Date
    May 2016
    Posts
    424
    Rep Power
    25

    Re: Konica Minolta C368 P-22

    Quote Originally Posted by Kenny View Post
    it then brings up a P-14 code
    Reset print heads (you will hear clicking sound 4 times)
    Initialization and stabilization.
    OFF/ON

    You will solve P-14 with this.
    P-22 can be related with P-14, so should be gone along with P-14.
    If this doesn't help try to switch PH unit from a working machine and see if it helps.

  9. #19
    Senior Tech 250+ Posts
    Konica Minolta C368 P-22

    Kenny's Avatar
    Join Date
    Jun 2009
    Location
    Leeds
    Posts
    455
    Rep Power
    37

    Re: Konica Minolta C368 P-22

    Hi guys,

    just a quick update, i have replaced the PH UNIT and PHRYB and it has solved the issue!

    so just want to say a big thank you to everyones input, the support on this site is phenomenal!

  10. #20
    Service Manager 2,500+ Posts
    Konica Minolta C368 P-22

    Hansoon's Avatar
    Join Date
    Sep 2007
    Posts
    3,190
    Rep Power
    94

    Re: Konica Minolta C368 P-22

    Thanks for that valuable feed back, Kenny!

    Hans
    " Sent from my Intel 80286 using MS-DOS 2.0 "

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here