Results 1 to 8 of 8
  1. #1
    Field Supervisor 500+ Posts
    Brand new Press 6120 and Fiery MIC-4160

    copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    902
    Rep Power
    41

    Brand new Press 6120 and Fiery MIC-4160

    Hello all!

    Looking for a piece of a puzzle, of course installation instructions aren't perfect but I have a brand new Fiery installed on a new KM press 6120.

    Printing works, can see the fiery via web page, but when you press controller on the device I get a blank white screen that eventually times out to a page not found error.

    the fiery is connected to the device via the video cable (from the video board to the connector on the fiery, with that odd shaped hdmi cord and the network cable is connected to the net connector on the fiery (copier symbol) and the net connector on the newly installed video board, if you unplug the net connector the fiery immediately notices.

    also dip sw 40-7 is set to 0 for the fiery.

    What am I Missing?

    Regards!
    A.

  2. #2
    Field Supervisor 500+ Posts
    Brand new Press 6120 and Fiery MIC-4160

    tulintron's Avatar
    Join Date
    Jul 2014
    Location
    Belo Horizonte, Minas Gerais
    Posts
    562
    Rep Power
    27

    Re: Brand new Press 6120 and Fiery MIC-4160

    Quote Originally Posted by copytechman View Post
    Hello all!

    Looking for a piece of a puzzle, of course installation instructions aren't perfect but I have a brand new Fiery installed on a new KM press 6120.

    Printing works, can see the fiery via web page, but when you press controller on the device I get a blank white screen that eventually times out to a page not found error.

    the fiery is connected to the device via the video cable (from the video board to the connector on the fiery, with that odd shaped hdmi cord and the network cable is connected to the net connector on the fiery (copier symbol) and the net connector on the newly installed video board, if you unplug the net connector the fiery immediately notices.

    also dip sw 40-7 is set to 0 for the fiery.

    What am I Missing?

    Regards!
    A.
    Did you install the VI-509 kit?
    Nothing like day after day

  3. #3
    Field Supervisor 500+ Posts
    Brand new Press 6120 and Fiery MIC-4160

    tulintron's Avatar
    Join Date
    Jul 2014
    Location
    Belo Horizonte, Minas Gerais
    Posts
    562
    Rep Power
    27

    Re: Brand new Press 6120 and Fiery MIC-4160

    Nothing like day after day

  4. #4
    Field Supervisor 500+ Posts
    Brand new Press 6120 and Fiery MIC-4160

    copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    902
    Rep Power
    41

    Re: Brand new Press 6120 and Fiery MIC-4160

    Quote Originally Posted by tulintron View Post
    Did you install the VI-509 kit?
    Yes the vi-509 was installed , followed all instructions per vi kit and everything else. At least until the fiery refused to even turn on now. Go figure. Appears dead now . No nothing

  5. #5
    Trusted Tech 50+ Posts
    Brand new Press 6120 and Fiery MIC-4160


    Join Date
    Feb 2018
    Location
    Earth
    Posts
    73
    Rep Power
    11

    Re: Brand new Press 6120 and Fiery MIC-4160

    I know that its a new Fiery but check the fan on the cpu and make sure its spinning free.

  6. #6
    Senior Tech 250+ Posts PrintWhisperer's Avatar
    Join Date
    Feb 2018
    Location
    Wild West
    Posts
    317
    Rep Power
    23

    Re: Brand new Press 6120 and Fiery MIC-4160

    Did you enable IPv6 on the copier and set it to DHCP? The Fiery should configure the mfp for communications. This is how all the Kyo Fierys talk to the mfp, the video cable is just RIP data.
    "Being ignorant is not so much a shame, as being unwilling to learn" - Benjamin Franklin

  7. #7
    Field Supervisor 500+ Posts
    Brand new Press 6120 and Fiery MIC-4160

    copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    902
    Rep Power
    41

    Re: Brand new Press 6120 and Fiery MIC-4160

    Quote Originally Posted by PrintWhisperer View Post
    Did you enable IPv6 on the copier and set it to DHCP? The Fiery should configure the mfp for communications. This is how all the Kyo Fierys talk to the mfp, the video cable is just RIP data.
    I have seen that before but thereís no place to enable ip v6 that Iíve seen when you turn on the dip sw to enable the fiery controller (on the main body) , itís not quite like the non prod Km boxes that way.

    regardless I still need to deal with a fiery that just wonít even light up now in any fashion lol

    thanks for the input!

    Regards!
    A.

  8. #8
    Field Supervisor 500+ Posts
    Brand new Press 6120 and Fiery MIC-4160

    copytechman's Avatar
    Join Date
    Nov 2008
    Location
    Barrie, Ontario
    Posts
    902
    Rep Power
    41

    Re: Brand new Press 6120 and Fiery MIC-4160

    Quote Originally Posted by Markks View Post
    I know that its a new Fiery but check the fan on the cpu and make sure its spinning free.
    I will double check that too , thank you.

    Regards.
    A.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here