Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Head Tech 500+ Posts SmellsHot's Avatar
    Join Date
    Dec 2009
    Location
    Sault Ste Marie, MI
    Posts
    512
    Rep Power
    36

    Bizhub C360 w/C2152 error

    Got a strange one....
    Bizhub C360 with a C2152 error on it. I replaced Main drive assy(houses PS39,cl5,m1) and transfer belt last Wednesday. Code came back about 24hrs later on Thursday. I swapped out PRCB being the last part listed as abnormal in service manual. Machine worked for another 24hrs or so and error came back. I took machine back to shop for observation over the weekend. It worked fine both saturday and sunday. I copied and printed a few hundred pages to it both days(about equivalent to how much they do). Brought the machine back to them Monday morning. It worked fine for about another 24hrs and the code returned on Tuesday. I brought machine back into shop and replaced Power supply on machine. I then returned the machine to them and told them to move machine to a different location, because I was suspecting faulty power. They did so. BUT......the next day the code came back. I was unable to clear at customers site, so I brought machine back into shop and the code cleared here. I gave them a brand new C360 to use for the time being while I monitor their machine in shop. I'm still leaning towards a power issue in their building, until the code appeared in my shop, when I sent a print job to it.
    This is where I am at now. They have a loaner C360 installed yesterday. And I have their C360 which has the C2152 error on it once again that will not reset.
    Anyboday got any ideas?
    Firmware is at the newest level
    Everyone has the right to be stupid. Some people just abuse this privelage more than others

  2. #2
    Master Of The Obvious 10,000+ Posts
    Bizhub C360 w/C2152 error

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,445
    Rep Power
    462

    Re: Bizhub C360 w/C2152 error

    To confirm a power quality diagnosis you'll need to install a power quality analyzer, and leave it on-line for 48 hours. The better ones record specific power quality events, whether its a sag or a surge, and how much of one. I had three Kyocera FalconIII machines that were dropping off the network randomly, then would come back on and print the documents in the queue. I found surges exceeding 250vac, usually at 6:00 am and 3:30 pm.

    When the power was cleaned up, there weren't any more problems. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  3. #3
    Senior Tech 100+ Posts
    Bizhub C360 w/C2152 error

    blaze2000's Avatar
    Join Date
    Sep 2010
    Location
    Watertown, WI
    Posts
    232
    Rep Power
    30

    Re: Bizhub C360 w/C2152 error

    Here's something that may be of interest, take a look at the attached file. I can't access my 360 manual here and MKM.com isn't letting me download the manual but here's some other stuff to check


    If you cannot get the machine error to clear at all try this...
    1. Power the machine ON with the main power switch while holding the Utility key.
    2. Release the Utility key when Konica Minolta is displayed.
    3. Wait for the Trouble Reset icon to appear and then press the icon.
    4. Power the machine OFF and ON using the main power switch.

    Here's some things to check for proper operation as well...


    1. PC12 has failed.
    2. M11 (First transfer pressure retraction motor) has failed.
    3. Check the bypass area, I recall problems with wires in that area getting pinched in covers

    Attached Files Attached Files

  4. #4
    Technician
    Bizhub C360 w/C2152 error


    Join Date
    Oct 2010
    Location
    clinton
    Posts
    48
    Rep Power
    29

    Re: Bizhub C360 w/C2152 error

    Talk to your Konica DSM, they use to have a power analyzer that would loan dealers.

  5. #5
    Head Tech 500+ Posts SmellsHot's Avatar
    Join Date
    Dec 2009
    Location
    Sault Ste Marie, MI
    Posts
    512
    Rep Power
    36

    Re: Bizhub C360 w/C2152 error

    Think I might have got it.....it would appear that the CL5 and PS39 failed again. I replaced them and the code cleared. Now just gotta play the waiting game to see if it will hold! Thanks for the input everyone.....Still gonna throw a power monitor on their line once I get it....
    Everyone has the right to be stupid. Some people just abuse this privelage more than others

  6. #6
    CopyTech,MIKE 100+ Posts copytech,mike's Avatar
    Join Date
    Jun 2014
    Location
    Silver Spring MD
    Posts
    200
    Rep Power
    0

    Re: Bizhub C360 w/C2152 error

    Quote Originally Posted by SmellsHot View Post
    Got a strange one....
    Bizhub C360 with a C2152 error on it. I replaced Main drive assy(houses PS39,cl5,m1) and transfer belt last Wednesday. Code came back about 24hrs later on Thursday. I swapped out PRCB being the last part listed as abnormal in service manual. Machine worked for another 24hrs or so and error came back. I took machine back to shop for observation over the weekend. It worked fine both saturday and sunday. I copied and printed a few hundred pages to it both days(about equivalent to how much they do). Brought the machine back to them Monday morning. It worked fine for about another 24hrs and the code returned on Tuesday. I brought machine back into shop and replaced Power supply on machine. I then returned the machine to them and told them to move machine to a different location, because I was suspecting faulty power. They did so. BUT......the next day the code came back. I was unable to clear at customers site, so I brought machine back into shop and the code cleared here. I gave them a brand new C360 to use for the time being while I monitor their machine in shop. I'm still leaning towards a power issue in their building, until the code appeared in my shop, when I sent a print job to it.
    This is where I am at now. They have a loaner C360 installed yesterday. And I have their C360 which has the C2152 error on it once again that will not reset.
    Anyboday got any ideas?
    Firmware is at the newest level
    Replace the transfer belt unit!

  7. #7
    Aging Tech 10,000+ Posts
    Bizhub C360 w/C2152 error

    copier addict's Avatar
    Join Date
    Jul 2013
    Location
    Diamond
    Posts
    11,919
    Rep Power
    323

    Re: Bizhub C360 w/C2152 error

    Quote Originally Posted by copytech,mike View Post
    Replace the transfer belt unit!
    Why are you resurrecting all these dead threads?

  8. #8
    Technician
    Join Date
    Jul 2019
    Location
    selangor
    Posts
    24
    Rep Power
    10

    Re: Bizhub C360 w/C2152 error

    Km c364

    Cant detect paper size...

    Tried many size..but same problem

    Any solution?

    Sent from my TA-1021 using Tapatalk

  9. #9
    Master Of The Obvious 10,000+ Posts
    Bizhub C360 w/C2152 error

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,445
    Rep Power
    462

    Re: Bizhub C360 w/C2152 error

    I just came across this C2152 on a bizhub C220 recently:

    On the machine I was working on the waste bottle had backed up at the primary transfer belt waste. The spout blocked up with toner rocks, filled the cleaner unit, and sprayed toner throughout the chassis.

    That was three months ago. When I returned this last week the transfer waste looked fine/normal, but the C2152 code would not clear even momentarily. With the screws removed from the rear transfer belt rail, you can shift the rail 5mm to one side and reveal PS39. Once the sensor was blown out it worked like a charm.

    I hate to think what it would take to remove that rear transfer belt rail and consequently PS39. There are primary transfer contacts through the rear frame, probably requiring stripping the back of the rear frame ... and the front of the rear frame. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  10. #10
    CopyTech,MIKE 100+ Posts copytech,mike's Avatar
    Join Date
    Jun 2014
    Location
    Silver Spring MD
    Posts
    200
    Rep Power
    0

    Re: Bizhub C360 w/C2152 error

    Quote Originally Posted by copier addict View Post
    Why are you resurrecting all these dead threads?
    Because i feel like you jerk.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here