Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19

Thread: error c2801

  1. #11
    zaini
    Guest

    Re: error c2801

    Quote Originally Posted by rajmalini View Post
    i have already adjusted the TCR censor and that time error 6 was appearing and after that same error code was coming.

    now tell me what can i do?
    may be your AIDC sensor dirty

  2. #12
    Technician rahadyan himura's Avatar
    Join Date
    Jun 2012
    Location
    bandar seribegawan
    Posts
    24
    Rep Power
    19

    Re: error c2801

    error code C2801 is TCR output abnormality, if you want to solve it just do toner auto supply.
    in service mode, Imaging process adjustment and then toner auto supply.
    if still appear and do trouble reset, off your copier and press and hold utility/counter and then on machine same time until trouble reset appear. touch trouble reset and off and on again.
    i hope this can help u.. ^^

  3. #13
    Junior Member
    Join Date
    Oct 2011
    Location
    Tiruchirappalli,Tamilnadu
    Posts
    2
    Rep Power
    0

    Thumbs up Re: error c2801

    If u run TCR error 6 came. Just remove all developer from developer unit and put new developer. Then add toner . Again Run TCR adjust it will work. Best of luck

  4. #14
    Junior Member
    Join Date
    Jul 2015
    Location
    Lagos
    Posts
    4
    Rep Power
    0

    Re: error c2801 I THIN THIS UT NEEDS HELP AND NOT TO INSULTED LIKE A PROFFESSIONA TEC

    Quote Originally Posted by blackcat4866 View Post
    ... you're not a technician, are you?

    If you have to ask what TCR sensor adjust is, you should be calling a technician. You'll just make it worse, if that is at all possible.
    =^..^=
    \

    PLS if u cant assist the guy dont make him look foolish pls try to help him out by submitting possible solutions to him and not make him loose courage in visiting the site ok

    guy all u need to do is check out forr three major sections .
    1st make sure that the IDC sensors are in order by properly cleaning them up first then
    2ndly make sure that developing units are ok with good developer in it not over used developer and that is properly fixed ans seated well
    then alsp make sure that the first transfer rollers are perfectly in order in the transfer belt section , also make sure that the chargers are properly in order i mean they are clean and still very ok without any rust surface . am sur these should help God Speed bro

  5. #15
    Senior Tech 100+ Posts Arcadian's Avatar
    Join Date
    Feb 2010
    Posts
    197
    Rep Power
    24

    Re: error c2801

    Quote Originally Posted by blackcat4866 View Post
    A professional technician would know that you never run TCR sensor adjust with used and very probably degraded developer. Before you make it worse, please, please, please, get some professional help. You can't do this by yourself. =^..^=
    lets be honest here! most copier tech are oblivious, on what to do, you have to find a knowledgeable tech, most tech, play it by ear, or from the service manual, of course its not the tech fault, as company who hires him, and send him out, even though he might say he knows the machine just to keep his job, some tech just drags the issue, making it more costly, while yes there are a few good ones out there, its like a doctor, they are just guessing, unless you goto a specialist, even then, its guess work. sadly that the way it is.

    i would clean the machine thoroughly, vacuum out all toner residue, literally its hard work, but you might have a bad seal leaking, or a developer seal worn away and toner is going everywhere, cleaning is only a temp solution, you must find the leakage either in the drum or developer. Its good to have a tech one that specializes in your machine. that like finding a needle in a hay sack. good luck.

  6. #16
    Service Manager 2,500+ Posts
    error c2801

    Synthohol's Avatar
    Join Date
    Mar 2016
    Location
    north jersey
    Posts
    3,297
    Rep Power
    114

    Re: error c2801

    Quote Originally Posted by Arcadian View Post
    lets be honest here! most copier tech are oblivious, on what to do, not and keep their job long.
    you have to find a knowledgeable tech, as they have been advised here multiple times
    most tech, play it by ear, experience or from the service manual, THATS OUR JOB of course its not the tech fault, as company who hires him, if the surgeon sucks it's the medical schools fault? and send him out, even though he might say he knows the machine just to keep his job, lying will not help your reputation or the company's as well some tech just drags the issue, making it more costly, you mean thieves and scoundrels? while yes there are a few good ones out there, its like a doctor, they are just guessing, making an informed decision based on the combination of symptoms, physical evidence, theory and localized component testing and thorough inspection?
    unless you goto a specialist, even then, its guess work. sadly that the way it is. agree to disagree

    i would clean the machine thoroughly, vacuum out all toner residue, literally its hard work, but you might have a bad seal leaking, or a developer seal worn away and toner is going everywhere, cleaning is only a temp solution, you must find the leakage either in the drum or developer. Its good to have a tech one that specializes in your machine. that like finding a needle in a hay sack. good luck.
    and this thread is 14 months old...
    with any luck the machine is a boat anchor by now
    We know a thing or two because we've seen a thing or two.

  7. #17
    Service Manager 10,000+ Posts
    error c2801

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    14,197
    Rep Power
    374

    Re: error c2801 I THIN THIS UT NEEDS HELP AND NOT TO INSULTED LIKE A PROFFESSIONA TEC

    Quote Originally Posted by stanloy4 View Post
    \

    PLS if u cant assist the guy dont make him look foolish pls try to help him out by submitting possible solutions to him and not make him loose courage in visiting the site ok

    guy all u need to do is check out forr three major sections .
    1st make sure that the IDC sensors are in order by properly cleaning them up first then
    2ndly make sure that developing units are ok with good developer in it not over used developer and that is properly fixed ans seated well
    then alsp make sure that the first transfer rollers are perfectly in order in the transfer belt section , also make sure that the chargers are properly in order i mean they are clean and still very ok without any rust surface . am sur these should help God Speed bro
    Frankly I have to agree with BC on this one sounds like the OP has no damn clue on what's going on.
    Even some 'techs' shouldn't be in the industry.

    Sent from my SM-G960U using Tapatalk

  8. #18
    Senior Tech 100+ Posts Arcadian's Avatar
    Join Date
    Feb 2010
    Posts
    197
    Rep Power
    24

    Re: error c2801

    Quote Originally Posted by Synthohol View Post
    and this thread is 14 months old...
    with any luck the machine is a boat anchor by now

    haha so true!!! So true.

  9. #19
    Senior Tech 100+ Posts
    Join Date
    May 2018
    Location
    Hong Kong
    Posts
    189
    Rep Power
    9

    Re: error c2801

    Quote Originally Posted by zaini View Post
    may be your AIDC sensor dirty
    yes, clean it.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here