Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Field Supervisor 500+ Posts
    Konica 7165 intermitted Jamming just past fuser when paper flipping over


    Join Date
    Jan 2012
    Location
    Tulsa, Oklahoma
    Posts
    932
    Rep Power
    42

    Konica 7165 intermitted Jamming just past fuser when paper flipping over

    Is there a common problem for this. I am to the point of pulling my hair out.

  2. #2
    Field Supervisor 500+ Posts
    Konica 7165 intermitted Jamming just past fuser when paper flipping over


    Join Date
    Dec 2008
    Location
    Baltimore, Maryland
    Posts
    912
    Rep Power
    42

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    its flipping after the fuser? or before?

    never seen it flip after fuser only before.


    what kind of paper are they using?
    what size paper?
    Single sided or only during duplex?

    What do they have a 20 year old machine?
    what is the meter at?
    what is meter since last PM?

    Are they on a dedicated 10 Amp outlet (or whatever equivalent may be)?

  3. #3
    Field Supervisor 500+ Posts Luther's Avatar
    Join Date
    May 2006
    Location
    crystal lake ,Illinois
    Posts
    682
    Rep Power
    44

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    i think he means face down copies, not flipping, check both the one way bearings one on the fuser and one on the exit unit, also make sure all the springs are on the exit unit, the only way to check it is to remove the exit unit unit and check for the springs that put pressure on the white rollers

  4. #4
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,396
    Rep Power
    152

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    I think the common bit is that copier part, i bet thats the problem. If you get the answer please let me know i have been struggling with this for years now.



    The way to check the switchover is to run the copies face up to test for jams.

  5. #5
    Field Supervisor 500+ Posts
    Konica 7165 intermitted Jamming just past fuser when paper flipping over


    Join Date
    Dec 2008
    Location
    Baltimore, Maryland
    Posts
    912
    Rep Power
    42

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    i had a 920 that would never run face down only face up or duplex (which exits like face up). Turned out its was the exit sensor.
    Also run it without a finisher and see if it will print face down may be the first sensor in the finisher.


    I have not touched a 7165 in years but look for a sensor in the exit assembly - the machine is like a 600/601 just old as balls.


    start there and lets see what you find...

  6. #6
    Senior Tech 100+ Posts
    Konica 7165 intermitted Jamming just past fuser when paper flipping over


    Join Date
    Apr 2009
    Posts
    104
    Rep Power
    32

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    I've seen the ADU drive board cause this. That's the small board just in front of and below the fuser. And make sure you don't use a 55 cpm board in a 65 cpm machine cause they are not the same.

  7. #7
    Trusted Tech 50+ Posts
    Konica 7165 intermitted Jamming just past fuser when paper flipping over

    DelawareJim's Avatar
    Join Date
    Jan 2008
    Location
    Dover
    Posts
    65
    Rep Power
    33

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    Try this...pull the front plastic cover off of the front side of the FUSER section. Looking straight in at the front end of the fuser that you just opened up, look for a small white gear all the way to the lower left. Pull that gear off of its shaft (you will have to remove the little green jam removal knob and one c-clip). Pay attention to it's orientation as you pull it off as you can install it backwards. The gear has a one-way bearing inside that gets greasy. Just flush the grease out, clean the shaft, and reinstall. While you are in the area, there is another white gear with a one-way bearing about an inch up and to the right. You might as well clean and degrease that one too. Again take note to how that gear comes off as you can install that one backwards too (save yourself and just mark the outside of both gears with a Sharpie marker). You can clean both gears and shafts in just a few minutes. Hope that helps.

  8. #8
    RTFM!! 5,000+ Posts allan's Avatar
    Join Date
    Apr 2010
    Location
    Centurion
    Posts
    5,396
    Rep Power
    152

    Re: Konica 7165 intermitted Jamming just past fuser when paper flipping over

    Quote Originally Posted by BR549 View Post
    I've seen the ADU drive board cause this. That's the small board just in front of and below the fuser. And make sure you don't use a 55 cpm board in a 65 cpm machine cause they are not the same.

    I can confirm this dude to developer build up. but could be something else. On a 601 i remove the duplex entrance mylars (u shaped bracket) they wear out and cause jams machines run fine without them.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here