Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: fs-534 j72-17

  1. #1
    Trusted Tech 50+ Posts Issac-brock's Avatar
    Join Date
    Jan 2015
    Location
    Burlington
    Posts
    60
    Rep Power
    10

    fs-534 j72-17

    I am having issues with a few different bizhub models connected to fs-534 finishers.
    The jam code is J72-17, paper is cutting the plastic paddles in the staple/ejector section. I have replaced the paddles on a finisher connected to a BH C554 with several hundred thousand prints but today ran into a c754e with just 69k on it. This is a very recent install but the guides are already cut. I see no adjustments for centering the finisher and only 1 adjustment for the paddle distance which when adjusted makes it worse.
    I adjusted tray 3 and 4 to try and centre them according to the marks on the trays. Couldn't make it jam on both Machines but the evidence is in the blue bin and jam codes.

    Anyone dealt with this?

    Thanks,
    Colin

  2. #2
    Master Of The Obvious 10,000+ Posts
    fs-534 j72-17

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    17,612
    Rep Power
    297

    Re: fs-534 j72-17

    I've seen it as low as 60K. My theory is that the paper positioning in the tray affects which side (front or back), will have the paper cuts. Logically you should be able to center the paper in the tray to minimize the paper cuts. The next time I see one, I'll try nudging the paper in the busiest tray away from the paper cuts. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  3. #3
    Trusted Tech 50+ Posts Issac-brock's Avatar
    Join Date
    Jan 2015
    Location
    Burlington
    Posts
    60
    Rep Power
    10

    Re: fs-534 j72-17

    Quote Originally Posted by blackcat4866 View Post
    I've seen it as low as 60K. My theory is that the paper positioning in the tray affects which side (front or back), will have the paper cuts. Logically you should be able to center the paper in the tray to minimize the paper cuts. The next time I see one, I'll try nudging the paper in the busiest tray away from the paper cuts. =^..^=
    I agree, I've tried to adjust the tray 3 and 4 (lct trays, built in) as centre as possible as these seem to be the primary source of the issue so far. Sad there seems to be no documentation on the centering procedure unless I have missed it,

  4. #4
    Master Of The Obvious 10,000+ Posts
    fs-534 j72-17

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    17,612
    Rep Power
    297

    Re: fs-534 j72-17

    I looked, and didn't see a centering procedure for the stapling tray regulator plates. If you find such a procedure I would be interested in hearing about it.

    As a temporary fix I have had success with filing smooth the regulator plates where the paper cuts occur, and it seems to take longer to re-occur. It's not the most pleasant job to get to them, maybe 75 minutes beginning to end.

    For those who haven't seen this, here are a few pix:

    Regulator Plate1.jpgRegulator Plate2.jpg

    =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  5. #5
    Trusted Tech 50+ Posts Issac-brock's Avatar
    Join Date
    Jan 2015
    Location
    Burlington
    Posts
    60
    Rep Power
    10

    Re: fs-534 j72-17

    I found a bulletin that mentions j72-16 and j72-18 but had a mod that fits my issue. I add the mylars as my machine started to jam again on large runs. I took out both guide assemblies and they were both cut pretty good. Lucky I had a strip of mylar the exact width described. The part # of the mylar was A00J561000.

    bulletin # TAUS1400198EN


    Highlights of bulletin
    paper guide mode from TAUS1400198EN.pdf

    Here is a shot of my modded machine. Also turned off the Offset Feature in Printing Defaults.
    modded guide.JPG


  6. #6
    Master Of The Obvious 10,000+ Posts
    fs-534 j72-17

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    17,612
    Rep Power
    297

    Re: fs-534 j72-17

    Thanks for sharing. Let me know how it goes. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  7. #7
    Trusted Tech 50+ Posts Issac-brock's Avatar
    Join Date
    Jan 2015
    Location
    Burlington
    Posts
    60
    Rep Power
    10

    Re: fs-534 j72-17

    First day of feedback, no jams. Users reported no issue, they run a large batch evey morning with about 2500 pages per day.

  8. #8
    Senior Tech 250+ Posts
    Join Date
    Oct 2014
    Location
    wareham.mass
    Posts
    275
    Rep Power
    13

    Re: fs-534 j72-17

    Is their a good way to installation of these guide's! Not sure on how to install this mode?

  9. #9
    Trusted Tech 50+ Posts Issac-brock's Avatar
    Join Date
    Jan 2015
    Location
    Burlington
    Posts
    60
    Rep Power
    10

    Re: fs-534 j72-17

    Quote Originally Posted by antone View Post
    Is their a good way to installation of these guide's! Not sure on how to install this mode?
    You need to remove the assemblies, takes about an hour to an hour and a half to complete.

  10. #10
    Senior Tech 250+ Posts
    Join Date
    Oct 2014
    Location
    wareham.mass
    Posts
    275
    Rep Power
    13

    Re: fs-534 j72-17

    Thanks you!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here