Results 1 to 7 of 7
  1. #1
    Junior Member
    Join Date
    Jan 2022
    Location
    konya
    Posts
    7
    Rep Power
    0

    kyocera taskalfa 300ci transfer belt and drums horizantel lines

    hello evreyone i have kyocera taskalfa 300ci the primery transfer belt stucking on drums and leave a horizantel line on drums and transfer belt after 3 days not working
    l changed the primery transfer belt and drums unites orginal but im scared about the problem prisest again
    any idea thanks and im sorry for my bad languge

  2. #2
    Field Supervisor 500+ Posts
    kyocera taskalfa 300ci transfer belt and drums horizantel lines

    dalewb74's Avatar
    Join Date
    Feb 2018
    Posts
    896
    Rep Power
    29

    Re: kyocera taskalfa 300ci transfer belt and drums horizantel lines

    well if you replaced the transfer belt and the drums you should be good. i wouldn't worry about it.

  3. #3
    Junior Member
    Join Date
    Jan 2022
    Location
    konya
    Posts
    7
    Rep Power
    0

    Re: kyocera taskalfa 300ci transfer belt and drums horizantel lines

    Quote Originally Posted by dalewb74 View Post
    well if you replaced the transfer belt and the drums you should be good. i wouldn't worry about it.
    dalewb74 thanks for replay im worry about the transfer belt touching the surface of drums and if customer dosnt use the machine about 2 or 3 days
    is the problem apper again .
    there is a motor inside the transfer unit is there any adjustment in service mode for it
    i cant found anything in service manual and bulten
    regards

  4. #4
    Field Supervisor 500+ Posts
    Join Date
    Aug 2011
    Posts
    580
    Rep Power
    57

    Re: kyocera taskalfa 300ci transfer belt and drums horizantel lines

    in case of not working color release motor, you get C2700.
    Check the motor by U030/ Color Release Motor (you can hear if it works or not)
    1. i would check drive by U030
    2. reconnect YC 28 on engine pwb
    3. check connector for belt for bent pin (not connector from belt itself, connector located on front frame)
    CRS.JPG
    in worst case, new engine pwb needed....that would be a total economic disaster

  5. #5
    Junior Member
    Join Date
    Jan 2022
    Location
    konya
    Posts
    7
    Rep Power
    0

    Re: kyocera taskalfa 300ci transfer belt and drums horizantel lines

    Quote Originally Posted by KYO_OEM View Post
    in case of not working color release motor, you get C2700.
    Check the motor by U030/ Color Release Motor (you can hear if it works or not)
    1. i would check drive by U030
    2. reconnect YC 28 on engine pwb
    3. check connector for belt for bent pin (not connector from belt itself, connector located on front frame)
    CRS.JPG
    in worst case, new engine pwb needed....that would be a total economic disaster
    thank you for repaly KYO_OEM im already checked it im hearing the color realse motor and connector but when i shutting down the machine there is about 1m.m space betwen transfer belt and drums is it normal?

  6. #6
    Field Supervisor 500+ Posts
    Join Date
    Aug 2011
    Posts
    580
    Rep Power
    57

    Re: kyocera taskalfa 300ci transfer belt and drums horizantel lines

    i am sorry, but i do not remember the distance between belt and drums on this very old system anymore.
    1mm can be ok, because the motor don`t lift the belt, it`s for the transfer rollers CMY only.
    If you mount the belt, the complete unit would lifted at the last 1-2 cm.
    But i remember 1 very old case with broken part in this area.
    The rear rail was broken and disassembling/ reassembling was a nightmare.
    Take care for #13 on fig 3/ frames 1/ Rail Image Rear.
    If you can lift up the belt in this area, new rail needed.
    the belt is no longer in a horizontal position
    it is slightly lower at the rear
    Rail.JPG

  7. #7
    Junior Member
    Join Date
    Jan 2022
    Location
    konya
    Posts
    7
    Rep Power
    0

    Re: kyocera taskalfa 300ci transfer belt and drums horizantel lines

    Quote Originally Posted by KYO_OEM View Post
    i am sorry, but i do not remember the distance between belt and drums on this very old system anymore.
    1mm can be ok, because the motor don`t lift the belt, it`s for the transfer rollers CMY only.
    If you mount the belt, the complete unit would lifted at the last 1-2 cm.
    But i remember 1 very old case with broken part in this area.
    The rear rail was broken and disassembling/ reassembling was a nightmare.
    Take care for #13 on fig 3/ frames 1/ Rail Image Rear.
    If you can lift up the belt in this area, new rail needed.
    the belt is no longer in a horizontal position
    it is slightly lower at the rear
    Rail.JPG
    ok thank you for your help i well control it
    have a nice day

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here