Tab Content
  • aAandy's Avatar
    21 Hours Ago
    aAandy started a thread HP DJ Z5400 in HP
    helloooo!!! have a machine which is calling new & full inks 'faulty', check the ink info and the expiry date on the 'faulty' carts is showing as...
    3 replies | 71 view(s)
  • aAandy's Avatar
    21 Hours Ago
    yes, only K toner supply port is blocking and jamming the toner supply/waste toner drive - i've dismantled quite a few to fix the waste toner problem...
    5 replies | 139 view(s)
  • aAandy's Avatar
    1 Day Ago
    hello everyone this machines' K toner port is blocking up causing a horrid clicking sound in the toner/waste toner drive system - vacuum out the...
    5 replies | 139 view(s)
  • aAandy's Avatar
    1 Week Ago
    aAandy replied to a thread [Jamming] HP LJ Pro M476 in HP
    after 34 years of printer repairs, neither do i as these are the first things any tech checks before consulting other techs thank you kindly for...
    9 replies | 537 view(s)
  • aAandy's Avatar
    1 Week Ago
    aAandy replied to a thread [Jamming] HP LJ Pro M476 in HP
    new - curious to know what you think a feed roller may have to do with the ITB stopping when paper reaches registration?
    9 replies | 537 view(s)
  • aAandy's Avatar
    1 Week Ago
    aAandy replied to a thread [Jamming] HP LJ Pro M476 in HP
    110k, paper sensor flags all operate normally, transfer & fuser look fine - ITB stops just for a moment when paper reaches registration, then jams...
    9 replies | 537 view(s)
  • aAandy's Avatar
    2 Weeks Ago
    aAandy replied to a thread [Jamming] HP LJ Pro M476 in HP
    bump anyone? anything?
    9 replies | 537 view(s)
  • aAandy's Avatar
    2 Weeks Ago
    aAandy replied to a thread [CQ] Bizhub C353 weird background in Konica Minolta
    by printing out the meter page with the laser slit glass cleaning wand in place i believe i have eliminated the possibility of arcing - i got a blank...
    12 replies | 483 view(s)
  • aAandy's Avatar
    2 Weeks Ago
    aAandy replied to a thread [CQ] Bizhub C353 weird background in Konica Minolta
    not yet, tried reseating the RAM (and cleaning the contacts), trimming ribbon cables, etc etc but no change, so i've ordered a used MFP board from...
    12 replies | 483 view(s)
  • aAandy's Avatar
    3 Weeks Ago
    aAandy replied to a thread [CQ] Bizhub C353 weird background in Konica Minolta
    did a stop test, background is on drums, ITB is being cleaned properly and fuser is in good condition
    12 replies | 483 view(s)
  • aAandy's Avatar
    3 Weeks Ago
    start by installing genuine carts - the cyan doesn't look like it's quite the right color and i've seen this a few times
    1 replies | 324 view(s)
  • aAandy's Avatar
    3 Weeks Ago
    aAandy replied to a thread [CQ] Bizhub C353 weird background in Konica Minolta
    it is being written to the drums by the lasers - left the laser slit glass wand in K and printed out a meter count list - obviously no print, but...
    12 replies | 483 view(s)
  • aAandy's Avatar
    3 Weeks Ago
    aAandy started a thread [Jamming] HP LJ Pro M476 in HP
    ITB stops momentarily when paper reaches transfer roller, resulting in a z-fold jam - as a temp measure i cut down the transfer roller springs to...
    9 replies | 537 view(s)
  • aAandy's Avatar
    3 Weeks Ago
    hey people anyone seen this sort of thing before? i've checked the obvious and the machine recently had new imaging units fitted, i suspect HVT,...
    12 replies | 483 view(s)
No More Results
About aAandy

Basic Information

Age
53
About aAandy
Real Name:
Andy
Country:
Australia
Where are you from (City, State):
Brisbane
Biography:
field service engineer with 30+ yrs experience repairing all makes and models of copier, printer, fax, MFC, plotter, scanner, mail opening machines, franking machines, rotary & laser engravers, 3D printers, microfiche reader/printers & computers/peripherals all to component level
Interests:
fishing
Occupation:
self employed field service engineer
What Year Did You Start in this Industry:
1983
Most Hated Brand:
HP
What was the first machine you worked on:
NEC COM (Computer Output to Microfiche)
Last machine you were formally trained on:
N/A
Gender:
Male

Statistics


Total Posts
Total Posts
289
Posts Per Day
0.10
General Information
Last Activity
1 Minute Ago
Join Date
04-18-2012
Referrals
1

03-24-2020


03-18-2020


03-07-2020