Tab Content
  • acribari's Avatar
    3 Days Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    Ah, that makes sense. I did not have any formal training on this model. Just have the service documentation. Thanks for all the help. ;)
    19 replies | 727 view(s)
  • acribari's Avatar
    3 Days Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    Thank you very much for the info. I went to the account today and ran 50-10 on HCT Bypass tray and the data setting was on 48. I had to move it to...
    19 replies | 727 view(s)
  • acribari's Avatar
    4 Days Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    No I have not tried sim 50-10. The high cap trays are centered so will this mess them up if I use sim 50 -10? I can go back and give it a try. ...
    19 replies | 727 view(s)
  • acribari's Avatar
    4 Days Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    Does anybody have an answer for this issue? I need to center the image on 12 X 18 and all other paper sizes from the multi bypass tray. The...
    19 replies | 727 view(s)
  • acribari's Avatar
    1 Week Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    Ok I will give it a try. I posted at the same time you did. Make sure we are talking about the same bypass model. Thanks
    19 replies | 727 view(s)
  • acribari's Avatar
    1 Week Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    All sizes. It does recognize 12 X 18 is loaded. I ran sim 40-2 but not sure if I did the correct sim. I have bypass tray Model MX-MF11. it sits...
    19 replies | 727 view(s)
  • acribari's Avatar
    1 Week Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    ok, so all the trays are feeding with the paper centered. The bypass tray is the problem. I can't seem to center the image. the bottom of the...
    19 replies | 727 view(s)
  • acribari's Avatar
    1 Week Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    How do you acquire a template for the media ? I'm not sure how to do this. I am new on this machine model. I am actually going over there now...
    19 replies | 727 view(s)
  • acribari's Avatar
    1 Week Ago
    acribari replied to a thread Sharp MX-M904 Image Shift in Sharp
    I will be going over there on Friday. I will get back to you with more details. Basically they have a pre perforated sheet of about 20 tickets or...
    19 replies | 727 view(s)
  • acribari's Avatar
    1 Week Ago
    Hello again, I have a customer that is trying to run perforated tickets on pre perforated paper. The image does not line up in the center of...
    19 replies | 727 view(s)
  • acribari's Avatar
    2 Weeks Ago
    acribari replied to a thread Sharp MX-M904 Still Good? in Sharp
    I figured it out. One of the exit rollers was not snapped in all the way and it prevented the height sensor from not actuating. After snapping the...
    24 replies | 1878 view(s)
  • acribari's Avatar
    3 Weeks Ago
    acribari replied to a thread Sharp MX-M904 Still Good? in Sharp
    Grrrrrrr. I have another issue with the finisher. FN-22 finisher. the exit lift errors out. F0-03. Any clues. I tried a sensor and it still...
    24 replies | 1878 view(s)
  • acribari's Avatar
    3 Weeks Ago
    acribari replied to a thread Sharp MX-M904 Still Good? in Sharp
    Great!!! Thank you both for the replies. I will try this next call. Thanks again.
    24 replies | 1878 view(s)
  • acribari's Avatar
    3 Weeks Ago
    acribari replied to a thread Sharp MX-M904 Still Good? in Sharp
    Ok, I finally got the machine all installed and it has been running good. I had some issues with the finisher but I got that resolved. Now, I...
    24 replies | 1878 view(s)
  • acribari's Avatar
    4 Weeks Ago
    Instead of fiddling around with the finisher, since it is a new install for the customer, I got another finisher with the same options. FN22 with...
    17 replies | 1685 view(s)
No More Results
About acribari

Basic Information

Age
50
About acribari
Real Name:
Angelo Cribari
Country:
United States
Where are you from (City, State):
Camp Hill, PA
Biography:
Self Employed IT and Copier Tech.
Interests:
Electronics and Computers
What Year Did You Start in this Industry:
1989
What was the first machine you worked on:
Xerox 5090 / Docutech 135
Last machine you were formally trained on:
Konica C6501
Gender:
Male

Statistics


Total Posts
Total Posts
39
Posts Per Day
0.03
General Information
Last Activity
3 Days Ago
Join Date
08-10-2015
Referrals
0

10-23-2019