Tab Content
  • mansart's Avatar
    1 Day Ago
    mansart replied to a thread MX4070n wireless not shownin network settings in Sharp
    OK I have taken the usb wireless card from a MX4071 and plugged into my PC. I sets up as Philips USB wireless adapter for a TV pta-01
    see more
    7 replies | 321 view(s)
  • mansart's Avatar
    1 Day Ago
    mansart replied to a thread MX4070n wireless not shownin network settings in Sharp
    And they have taken care of that confusion and come up with the completely new naming convention of BP70C31
    see more
    7 replies | 321 view(s)
  • mansart's Avatar
    1 Day Ago
    mansart replied to a thread MX4070n wireless not shownin network settings in Sharp
    It does work. I stand corrected. Wireless card from MX4071 into a MX4071S works once 26-50 is done.
    see more
    7 replies | 321 view(s)
  • mansart's Avatar
    1 Day Ago
    mansart replied to a thread MX4070n wireless not shownin network settings in Sharp
    "Also, it is possible, that the wireless nic card is scrapped. Some confusing 2022 models comes without WLAN NICs because of chip shortages, and they...
    see more
    7 replies | 321 view(s)
  • mansart's Avatar
    6 Days Ago
    mansart replied to a thread [Error Code] F6-00 on MXC303wW / MXC304W in Sharp
    Fax line is not being used in this case, so there is no phone line plugged in at all. I've seen this occur on MXC301's when fax line not plugged...
    see more
    5 replies | 269 view(s)
  • mansart's Avatar
    6 Days Ago
    mansart replied to a thread disable fax in Sharp
    I tried this on a MXM455 after seeing your post. Initially looks like it will work but after about 10 minutes will throw F6-00 Sent from my...
    see more
    7 replies | 338 view(s)
  • mansart's Avatar
    1 Week Ago
    mansart replied to a thread disable fax in Sharp
    I'm not a betting man, but if I were, I would bet on the horse named "Error Code" I would assume that just unplugging fax board would result in...
    see more
    7 replies | 338 view(s)
  • mansart's Avatar
    1 Week Ago
    mansart replied to a thread Sharp MXC300W in Sharp
    Try using IP address of MAC instead of host name to rule out DNS issue What are you getting for am error? Sent from my iPhone using Tapatalk
    see more
    8 replies | 382 view(s)
  • mansart's Avatar
    2 Weeks Ago
    mansart replied to a thread Sharp MXC300W in Sharp
    Setting Up Sharp MFPs to Scan to FTP on MACs (lesolson.com)
    see more
    8 replies | 382 view(s)
  • mansart's Avatar
    2 Weeks Ago
    mansart replied to a thread Sharp MXC300W in Sharp
    Here is a decent walk through on set up of SMB to a MAC. Setup SMB Scanning Using Mac OS X (10.11.x, 10.12.X) (xerox.com) Your problem is going...
    see more
    8 replies | 382 view(s)
  • mansart's Avatar
    2 Weeks Ago
    mansart replied to a thread Sharp MX2640 in Sharp
    Cycle power. Get machine to state where doc feed will work. Don't feed originals. Go to SIM 2-2, take picture of display, it will show you what...
    see more
    4 replies | 429 view(s)
  • ZOOTECH's Avatar
    3 Weeks Ago
    ZOOTECH replied to a thread Sharp 70/71 series maintenance code suppression? in Sharp
    I found this info on line by mistake, not really sure how I got there. Stop Maintenance Counter: Set 21-1 to 999 (free) Stop Drum Maintenance:...
    see more
    6 replies | 665 view(s)
  • mansart's Avatar
    3 Weeks Ago
    mansart replied to a thread SHARP MX3570V in Sharp
    You mentioned LSU good? Did you do LSU check 66-1? I’m not sure if it’s the scan of the samples or not but the more I zoom in on them…you...
    see more
    32 replies | 2039 view(s)
  • mansart's Avatar
    3 Weeks Ago
    mansart replied to a thread SHARP MX3570V in Sharp
    Wow! That’s a good one. Have not seen this before. I’m assuming the page with bold “Forum” and “Tournament “ is first out? Is the toner fused...
    see more
    32 replies | 2039 view(s)
  • mansart's Avatar
    3 Weeks Ago
    mansart replied to a thread SHARP MX3570V in Sharp
    The actual mechanics of paper xport, placing image and fusing image on paper are the same for both copy and print. I'm not saying its impossible,...
    see more
    32 replies | 2039 view(s)
  • mansart's Avatar
    4 Weeks Ago
    mansart replied to a thread SHARP MX3570V in Sharp
    Only on print jobs? What about copy jobs? Sent from my iPhone using Tapatalk
    see more
    32 replies | 2039 view(s)
No More Results
About mansart

Basic Information

About mansart
Real Name:
Michael Ansart
Country:
United States
What Year Did You Start in this Industry:
1986
What was the first machine you worked on:
Ricoh FT6200
Last machine you were formally trained on:
Sharp MXC311
Gender:
Male

Statistics


Total Posts
Total Posts
775
Posts Per Day
0.16
General Information
Last Activity
9 Hours Ago
Join Date
04-30-2009
Referrals
0

4 Friends

  1. abangcopier abangcopier is offline

    Junior Member

    abangcopier

  2. prntrfxr prntrfxr is offline

    Service Manager

    prntrfxr

  3. Smarttowers Smarttowers is offline

    Junior Member

    Smarttowers

  4. ZOOTECH ZOOTECH is offline

    Senior member of CRS

    ZOOTECH
Showing Friends 1 to 4 of 4

05-24-2022


05-23-2022


05-18-2022


05-17-2022


05-11-2022


05-10-2022


05-06-2022


05-05-2022


05-04-2022


05-01-2022


04-29-2022