View Profile: mloudy - Copytechnet.com

13 Hours Ago

mloudy replied to a thread MX-B467P with toner spots in Sharp

Lexmark is really good at listing every change that is included in a new firmware. I have only seen Sharp at the same firmware level as the Lexmark...

6 replies | 574 view(s)

3 Days Ago

mloudy replied to a thread Co Inquiry about sharp series 4 in Sharp

SF-741 SF-9500 Heck I even worked on memeographs and duplicators. I just turned 55. I started working in this field at 15.

7 replies | 903 view(s)

3 Days Ago

mloudy replied to a thread MX-B467P with toner spots in Sharp

Lexmark M1246 I think. I have not seen this issue.

6 replies | 574 view(s)

4 Days Ago

mloudy replied to a thread [Error Code] MX-3571 U2-74 in Sharp

We replaced the MFPC-SCAN PWB on 11/8/2021 and the U2-74 has not returned. We updated the firmware prior to that and then on the next call installed...

6 replies | 521 view(s)

1 Week Ago

mloudy replied to a thread Lexmark Cloud Fleet Management in Lexmark

I have not seen a way to do this.

1 replies | 294 view(s)

1 Week Ago

mloudy replied to a thread Sharp MX-B455W error F2-40 in Sharp

New style

7 replies | 1015 view(s)

1 Week Ago

mloudy replied to a thread Sharp MX-B455W error F2-40 in Sharp

The little horseshoe shape bit at the rear of the copier that locks the toner cartridge in. If you remove the toner and look into the opening you...

7 replies | 1015 view(s)

2 Weeks Ago

mloudy replied to a thread [Misc] Lexmark MS823 Drums in Lexmark

There was a warehouse fire in China? Do tell.. I thought this was a Ninestar issue.

4 replies | 535 view(s)

2 Weeks Ago

mloudy replied to a thread BP-70C31 Drum Cartridge Error in Sharp

This info isn't for this problem but another "install drum" error that can occur at set-up. The waste toner box that comes with the machine is...

7 replies | 854 view(s)

2 Weeks Ago

mloudy replied to a thread MX-FN30 stapler cardtridgr holder in Sharp

This are often difficult to find in the Parts Guide. If you open the Parts guide and search "cartridge" you can normally find it. There is a document...

3 replies | 406 view(s)

2 Weeks Ago

mloudy replied to a thread Lexmark ms811dn fuser reset? in Lexmark

Haven't seen it often but we have encountered the PM message remain after installing a new OEM Lexmark PM kit in this series. I have been able to...

8 replies | 4668 view(s)

3 Weeks Ago

mloudy replied to a thread Sharp Mx4071 slow to boot and run in Sharp

Is there any chance the eeprom was installed backwards in the field prior to being picked up? I just read the Handy Guide instructions for proper...

16 replies | 1813 view(s)

3 Weeks Ago

mloudy replied to a thread Sharp Mx4071 slow to boot and run in Sharp

If you are able to export the 22-6 to a USB drive open the txt file and scroll down to almost the bottom. You will see the HDD. Likely a Toshiba...

16 replies | 1813 view(s)

3 Weeks Ago

mloudy replied to a thread Sharp Mx4071 slow to boot and run in Sharp

I know you have installed a different HDD but that sounds like a bad HDD to me. Can you export the 22-6 to a thumb drive?

16 replies | 1813 view(s)

3 Weeks Ago

mloudy replied to a thread Sharp Mx4071 slow to boot and run in Sharp

I had a tech break 1 leg off of one of those chips. I was able to put it in my eeprom programmer and hold a paper clip against the tiny exposed...

16 replies | 1813 view(s)

3 Weeks Ago

mloudy replied to a thread Sharp Mx4071 slow to boot and run in Sharp

For the U2-00 I would inspect the 8 pin eeprom that you moved from the old SCN pwb to the new SCN pwb. Make sure it is installed in the correct...

16 replies | 1813 view(s)

3 Weeks Ago

bigdaddyooo started a thread MX-FN22 saddle skew in Sharp

Anyone ever have to adjust the skew of 11x17 after saddle stitch has taken place? When you look at the folded print, the top line of paper doesn't...

0 replies | 241 view(s)

3 Weeks Ago

mloudy replied to a thread RJ Young service with unlimited pages in Business Talk

There are many pages to this post so I don't rememebr if this was linked on any of them. Is It the End of the Road for Flat-Rate Billing? There...

95 replies | 4942 view(s)

4 Weeks Ago

mloudy replied to a thread Lexmark m5155 invalid factory configuration 32.01 in Lexmark

I do not know what causes this. I have seen it only three times.

8 replies | 746 view(s)

4 Weeks Ago

mloudy replied to a thread Lexmark m5155 invalid factory configuration 32.01 in Lexmark

It should be the UN and PW you use for all your Lexmark Dealer sites. If you aren't a Lexmark Dealer you will need to find one to service this...

8 replies | 746 view(s)

4 Weeks Ago

mloudy replied to a thread Lexmark m5155 invalid factory configuration 32.01 in Lexmark

You will need to use the Factory Restore Tool. Go to the site, enter the SN and it will give you files to install and the order in which to install...

8 replies | 746 view(s)

4 Weeks Ago

mloudy replied to a thread Sharp \ Lexmark cross reference in Sharp

No. Perhaps the waste containers but not the toners or image units. I was able to get DV units of a XC4140 to work in a MX-C407F so I think...

11 replies | 3352 view(s)

mloudy
Field Supervisor
500+ Posts

Mini Statistics

More 1 Friend

bigdaddyooo

Recent Visitors

Basic Information

About mloudy

Statistics

Total Posts

General Information

1 Friend

bigdaddyooo

12-05-2023

12-04-2023

12-02-2023

12-01-2023

11-27-2023

11-25-2023

11-24-2023

11-23-2023

11-22-2023

11-20-2023

11-17-2023

mloudy Field Supervisor 500+ Posts

Mini Statistics

More 1 Friend

bigdaddyooo

Recent Visitors

Basic Information

About mloudy

Statistics

Total Posts

General Information

1 Friend

bigdaddyooo

12-05-2023

12-04-2023

12-02-2023

12-01-2023

11-27-2023

11-25-2023

11-24-2023

11-23-2023

11-22-2023

11-20-2023

11-17-2023

mloudy
Field Supervisor
500+ Posts