Samsung CLP300N

[leotzian]

It sounds to me like you could pay a print shop for a few pages a month, and save yourself a lot of money.

The Kyocera will certainly produce better prints than your Samsung. But keep in mind that these tabletop color printers never get the manufacturers suggested yield on the image units (closer to 50%). =^..^=

In a way you might be right but I live 50km from the nearest paint shop, so this is not a solution, I also have a OKI Laser monochrome printer for my black and white printings.

[leotzian]

Hi to all again, I had almost fixed my CLP300N I took off the cleaning plastic blade, and with a very good double sided tape, I put the up down, then there are 2 springs that pushes the metal plate in which the blade is secured, I made them a little longer by pulling them and now the metal plade is pushing the belt better, Now as many prints I will make all are the same.

A friend of mine bought a new printer and he gave me his old Samsung CLP310 is a little newer than mine, he had 2 problems the same with mine, tranfer belt was not cleaned by the blade, and a ghosting in the end of the page.
I had done the same fix, the belt is cleaned very good from print to print, but the ghosting is the same, I am sure that 100% is not from the belt.
As you can see before the fix the newer page had the image from the page already printed, and the ghosting, after the fix only the ghosting had remained.
I sent you 4 scans 2 before and 2 after the fix of the belt.
Please where to look concernig the ghosting?

Thanks you all for advance2019-12-17-0001.jpg2019-12-17-0002.jpg2019-12-17-0003.jpg2019-12-17-0004.jpg

[blackcat4866]

All my manuals were downloaded in Aug 2008, making your machine at least 11 years old. I would be very surprised if you could get any parts or consumables. =^..^=

Same answer as before. =^..^=

[leotzian]

Same answer as before. =^..^=

Yes, yes I know but if you know please tell me about the above problem.
To see the 10cm of the top of the page I print, printed again faint at the end of the page what is might be? do you know?

I want to add that the ghosting is 19cm, if I measure a sentence for example the same sentence is printing again after 19cm.

[Lance15]

Looks like a fuser problem.

This website says it all:
JC96-05491B - FUSER

[leotzian]

Looks like a fuser problem.

This website says it all:
JC96-05491B - FUSER

According to the service manual because the faint second image is repeated after about 19cm is the OPC DRUM unit

[Lance15]

What else can we say..........

https://media.giphy.com/media/RL0xU1daTlMoE/source.gif

[Phil B.]

What else can we say..........

https://media.giphy.com/media/RL0xU1daTlMoE/source.gif

F'n LOVE IT!

Thanks Brother.. have saved that one.. and you just might see it pop up in other posts in the future!

P.S. Da check is in the mail!

[leotzian]

F'n LOVE IT!

Thanks Brother.. have saved that one.. and you just might see it pop up in other posts in the future!

P.S. Da check is in the mail!

Perhaps there is a language issue, I don't want to affent anyone, I try to get some help. I am also an electronic technician....

I had searched all over the net and I found the cm of the ghosting if there was the fuser unit it must be very near , also I scratched the printing and all stays in place, I read if the fuser has less temperature the print will go away, and the page comes out very hot...

Sorry again..

[Phil B.]

Perhaps there is a language issue, I don't want to affent anyone, I try to get some help. Me also am an electronic technician....


I had searched all over the net and I found the cm of the ghosting if there was the fuser unit it must be very near , also I scratched the printing and all stays in place, I read if the fuser has less temperature the print will go away, and the page comes out very hot...

Sorry again..

Not completely true.
If belt is worn or damaged it will bond but lighter or in pattern..
Been at this shit fir 31+yrs.

Sent from my SM-G960U using Tapatalk