Results 1 to 8 of 8
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jul 2012
    Location
    sarawak
    Posts
    64
    Rep Power
    0

    Angry Mp7500 replace new developer 2801 initialize after that overtoning

    mp7500 replace new developer 2801 initialize after that print out overtoning check everything fine ...finally 5801 all memory clear
    and found out the 7 digits inside the 2801 erase so my question do i need initialize 2801 again & key in the 7 digits again


    thanks a lot

  2. #2
    Field Supervisor 500+ Posts Codex's Avatar
    Join Date
    May 2008
    Location
    Sicily
    Posts
    647
    Rep Power
    42

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    Quote Originally Posted by hsh6049 View Post
    mp7500 replace new developer 2801 initialize after that print out overtoning check everything fine ...finally 5801 all memory clear
    and found out the 7 digits inside the 2801 erase so my question do i need initialize 2801 again & key in the 7 digits again


    thanks a lot
    Why doing a Memory clear after changing developer???
    Normally if you enter again 2801 you can digit again and press "#" . It's not a "one time value".... You can digit again and again.

    Inviato dal mio SM-G935F utilizzando Tapatalk
    Memento Audere Semper

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Jul 2012
    Location
    sarawak
    Posts
    64
    Rep Power
    0

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    Quote Originally Posted by codex View Post
    why doing a memory clear after changing developer???
    Normally if you enter again 2801 you can digit again and press "#" . It's not a "one time value".... You can digit again and again.

    Inviato dal mio sm-g935f utilizzando tapatalk
    i been try whatever i can the dv tank full of toner unplug the toner end sensor running about more than 1000 copies and back to normal but sp2223 reading 11v and also check dv motor everything find
    still cannot solve

  4. #4
    Service Manager 1,000+ Posts
    Join Date
    Oct 2011
    Location
    Hunter Valley, NSW
    Posts
    1,020
    Rep Power
    57

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    You have bricked machine with memory clear, change dev again and any other parts that are due, input factory data from birth certificate then initialise dev. Good luck.
    NEVER CLEAR ALL MEMORY!

  5. #5
    Technician
    Mp7500 replace new developer 2801 initialize after that overtoning

    wilez's Avatar
    Join Date
    Jan 2011
    Posts
    49
    Rep Power
    0

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    That model was known to have mag brush ground and drum ground issues on high meters. Also if using aftermarket drums and toner will cause overtoning. as mentioned above start from scratch if possile.
    Make sure mag brush is contacting ground in rear, do new developer, drum, wires and grid then go through your adjustments.
    FYI! had to replace mag brush a couple of times to stop overtoning.

  6. #6
    Retired 10,000+ Posts
    Mp7500 replace new developer 2801 initialize after that overtoning

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,126
    Rep Power
    989

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    As for your question concerning the lot number for the developer being cleared, no big gig. It is merely the batch number of the developer and is stored for the record keeping purpose. Should Ricoh discovers a contaminated batch of developer, they will send out bulletin. You can then check the batch number on all your machines.

    As to running SP 5801-001, you have cleared ALL the factory settings from memory.

  7. #7
    Trusted Tech 50+ Posts
    Join Date
    Jul 2012
    Location
    sarawak
    Posts
    64
    Rep Power
    0

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    Quote Originally Posted by slimslob View Post
    As for your question concerning the lot number for the developer being cleared, no big gig. It is merely the batch number of the developer and is stored for the record keeping purpose. Should Ricoh discovers a contaminated batch of developer, they will send out bulletin. You can then check the batch number on all your machines.

    As to running SP 5801-001, you have cleared ALL the factory settings from memory.
    wht should i do next? ....now dvtank inside full of toner can i initialize 2801 again

  8. #8
    Retired 10,000+ Posts
    Mp7500 replace new developer 2801 initialize after that overtoning

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,126
    Rep Power
    989

    Re: Mp7500 replace new developer 2801 initialize after that overtoning

    Quote Originally Posted by hsh6049 View Post
    wht should i do next? ....now dvtank inside full of toner can i initialize 2801 again
    NO!!! Just keep a record of the lot number. If you really want to initialize the development unit again, use another new bag of developer.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here