Results 1 to 10 of 10
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jun 2017
    Location
    George
    Posts
    72
    Rep Power
    14

    MP7503 Jam Code 125 and SC720-42

    Hi Guys
    I have a MP7503 that comes up with the above mentioned errors.
    Jam Code 125 refers to Booklet Stapler Movement Motor Jam<
    After a few time the machine will go into SC720-42

    Corner stapler movement motor error (3K/2K Finisher)
    The stapler did not return to its home position within the prescribed number of
    pulses, or did not leave the home position within the prescribed number of
    pulses. The first occurrence issues a jam alert, the second issues this SC code.
    • Motor overload.
    • Motor harness, connector is loose, broken, or defective.
    • Stapler HP sensor harness, connector is loose, broken, or defective.
    • HP sensor defective
    • Motor, motor drive board defective.
    • Inspect the area around the motor for obstacles that could interfere with
    operation of the motor.
    • Inspect motor harness, connector and replace if damaged.
    • Inspect stapler HP sensor harness, connector and replace if damaged.
    • Replace corner stapler HP sensor.
    • Replace corner stapler movement motor.
    • Replace Finisher main board.<br><br>Motor function is intermittent. The one moment it will go out of HP and then after a few open and close doors it will stop. Moving it to the back of the finisher will in some cases see it come forward to HP, other cases just move a bit and then stop. And then sometimes nothing at all. I have replaced the motor and also tried running without any load with the same results.

    Any ideas???

  2. #2
    Service Manager 1,000+ Posts
    MP7503 Jam Code 125 and SC720-42

    guitar9199's Avatar
    Join Date
    Sep 2016
    Location
    Eveleth, MN
    Posts
    1,090
    Rep Power
    41

    Re: MP7503 Jam Code 125 and SC720-42

    First thing I would do is make sure the stapler isn't bound up. After that...follow the list.

  3. #3
    Retired 10,000+ Posts
    MP7503 Jam Code 125 and SC720-42

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,126
    Rep Power
    989

    Re: MP7503 Jam Code 125 and SC720-42

    Anytime you get both a Jam code and a service call code on a finisher, trouble the service code first. Normally the jam is created by the condition causing the service code.

  4. #4
    Service Manager 1,000+ Posts
    MP7503 Jam Code 125 and SC720-42

    GIUBOSS's Avatar
    Join Date
    Jul 2013
    Location
    Rome, IT
    Posts
    1,299
    Rep Power
    68

    Re: MP7503 Jam Code 125 and SC720-42

    I suggest you clean and lubricate the steel axes where the stapler slides. Don't leave that of the joggers behind. Scrutinize the movement with the door open.

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Jun 2017
    Location
    George
    Posts
    72
    Rep Power
    14

    Re: MP7503 Jam Code 125 and SC720-42

    I have removed the motor that moves the staple unit completely, so it has not load on. Still moves erratic. If i move the staple unit out of home position the motor should turn to get it back in HP. Sometimes it does and sometimes it does not.

  6. #6
    Senior Tech 100+ Posts
    Join Date
    Jul 2015
    Posts
    178
    Rep Power
    21

    Re: MP7503 Jam Code 125 and SC720-42

    Stapler harness.

  7. #7
    Technician
    Join Date
    Nov 2019
    Location
    Fresno, CA
    Posts
    37
    Rep Power
    9

    Re: MP7503 Jam Code 125 and SC720-42

    I would check the wire harness for any wires that are nicked. I had one machine that would do the staple job, and then throw an SC code. I replaced everything the manual suggested. It ended up being a wire that has some of the coating cut and it was grounding out. I wrapped it with tape and works perfect.

  8. #8
    Professional Moron 2,500+ Posts TonerMunkeh's Avatar
    Join Date
    Apr 2008
    Location
    Shitsville, UK
    Posts
    3,852
    Rep Power
    108

    Re: MP7503 Jam Code 125 and SC720-42

    Morning,

    Did you get anywhere with this? Got a 9003 with an SR4120 doing exactly the same thing.

  9. #9
    Trusted Tech 50+ Posts Batman1976's Avatar
    Join Date
    Jun 2016
    Location
    London
    Posts
    83
    Rep Power
    16

    Re: MP7503 Jam Code 125 and SC720-42

    Check the Mylars on the shift exit rollers. Remove them!!!

  10. #10
    Service Manager 1,000+ Posts
    MP7503 Jam Code 125 and SC720-42


    Join Date
    Nov 2007
    Location
    New Jersey
    Posts
    1,661
    Rep Power
    86

    Re: MP7503 Jam Code 125 and SC720-42

    Quote Originally Posted by MIKON View Post
    Stapler harness.
    +1 Stapler harness

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here