Results 1 to 7 of 7

Thread: Savin MP c3002

  1. #1
    Junior Member
    Join Date
    Aug 2020
    Location
    cleveland ohio
    Posts
    1
    Rep Power
    0

    Savin MP c3002

    Hey hey copytechnet, I am the end user of a Savin MP c3002 and I am getting the error code SC672-00 I am not factory trained but I have been talking with a service tech that does not live close by me. so far I Replace the D1425110 BCU and the D1425712 PCB and I'm ending with the same code at start up. does any one have some pointers for me ???


    Thanks so much ,



    Tyson

  2. #2
    Field Supervisor 500+ Posts
    Savin MP c3002

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    644
    Rep Power
    30

    Re: Savin MP c3002

    The error code 672 or SC672 is a controller startup error. It could mean the controller board is installed incorrectly or has gone bad. It could also be a simpler solution such as a connector somewhere is not securely fastened.

  3. #3
    Service Manager 5,000+ Posts
    Savin MP c3002

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    9,553
    Rep Power
    221

    Re: Savin MP c3002

    Quote Originally Posted by tysonkuchta View Post
    Hey hey copytechnet, I am the end user of a Savin MP c3002 and I am getting the error code SC672-00 I am not factory trained but I have been talking with a service tech that does not live close by me. so far I Replace the D1425110 BCU and the D1425712 PCB and I'm ending with the same code at start up. does any one have some pointers for me ???
    Thanks so much , Tyson
    did you CLEAR the error after replacing the boards?
    did you hook them up properly ?
    did you swap over the NVRAM from old to new?

    so many questions so few answers ...

    this SHOULD have been handled by a TRAINED service tech with THE MANUAL! There are certain procedures that MUST be followed PRECISELY IN THE PROPER ORDER!

  4. #4
    Field Supervisor 500+ Posts
    Savin MP c3002

    BillyCarpenter's Avatar
    Join Date
    Aug 2020
    Location
    Long Beach, Mississippi
    Posts
    644
    Rep Power
    30

    Re: Savin MP c3002

    Quote Originally Posted by Phil B. View Post
    did you CLEAR the error after replacing the boards?
    did you hook them up properly ?
    did you swap over the NVRAM from old to new?

    so many questions so few answers ...

    this SHOULD have been handled by a TRAINED service tech with THE MANUAL! There are certain procedures that MUST be followed PRECISELY IN THE PROPER ORDER!
    Yeo, and are these new or used PCBs? If used, do you know for sure they were working...did you actually see them in a working machine?

  5. #5
    Service Manager 2,500+ Posts
    Savin MP c3002

    sandmanmac's Avatar
    Join Date
    Feb 2009
    Location
    Toronto, ON
    Posts
    3,155
    Rep Power
    107

    Re: Savin MP c3002

    Quote Originally Posted by tysonkuchta View Post
    Hey hey copytechnet, I am the end user of a Savin MP c3002 and I am getting the error code SC672-00 I am not factory trained but I have been talking with a service tech that does not live close by me. so far I Replace the D1425110 BCU and the D1425712 PCB and I'm ending with the same code at start up. does any one have some pointers for me ???


    Thanks so much ,



    Tyson
    SC672 is one of the most wide-ranging error codes. It seems to be generally caused by a power surge that shorts out something.
    A couple of other things to try is remove/disconnect the Fax board (if installed), and also disconnect the HDD and try booting up the machine.
    If it boots it's obviously caused by one of the 2. Re-connect 1 at a time to determine which one.
    You might not even require the fax these days. If not, then you're good to go. But if it's the HDD, then you'll need to reformat/ replace it in order to use many features - specifically scanning.
    * Note if it does boot up without the HDD connected, you will see some error messages flashing in the bottom of the screen (Generally SC8xx) indicating an issue with the HDD.

  6. #6
    Service Manager 2,500+ Posts
    Savin MP c3002

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    4,672
    Rep Power
    97

    Re: Savin MP c3002

    Quote Originally Posted by tysonkuchta View Post
    Hey hey copytechnet, I am the end user of a Savin MP c3002 and I am getting the error code SC672-00 I am not factory trained but I have been talking with a service tech that does not live close by me. so far I Replace the D1425110 BCU and the D1425712 PCB and I'm ending with the same code at start up. does any one have some pointers for me ???


    Thanks so much ,



    Tyson

    Put all the original boards back on & see if the machine will accept a firmware update.
    Let us eat, drink, and be merry, because tomorrow we may die!

    www.copierfirmware.co.uk

  7. #7
    Copier Technician 500+ Posts
    Savin MP c3002

    mga's Avatar
    Join Date
    Dec 2010
    Location
    london
    Posts
    686
    Rep Power
    68

    Re: Savin MP c3002

    Quote Originally Posted by tysonkuchta View Post
    Hey hey copytechnet, I am the end user of a Savin MP c3002 and I am getting the error code SC672-00 I am not factory trained but I have been talking with a service tech that does not live close by me. so far I Replace the D1425110 BCU and the D1425712 PCB and I'm ending with the same code at start up. does any one have some pointers for me ???


    Thanks so much ,


    Tyson
    Hi you shouldn't start by replacing boards put the old pwb's back on and start from there

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here