Results 1 to 10 of 10
  1. #1
    Junior Member
    Join Date
    Oct 2020
    Location
    Taipei
    Posts
    4
    Rep Power
    0

    Ricoh C2003 - print job will do after re-close duplex unit

    as i describe in title, motors are not working after i press start for print job and counter list. Print jobs will work after i re-close duplex unit. But this problem will happen again when i reboot machine. Is there anyone experienced the same problem like this?

  2. #2
    Retired 10,000+ Posts
    Ricoh C2003 - print job will do after re-close duplex unit

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,128
    Rep Power
    989

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Check the Service Code log for any type C errors at power up. These are non fatal errors that are counted and logged only, they are not displayed.

  3. #3
    Junior Member
    Join Date
    Oct 2020
    Location
    Taipei
    Posts
    4
    Rep Power
    0

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    i found SC552-02, check Fusing Temperature with SP MODE 1-106, it is 45 deg after standby for a while, after re-close duplex unit, it will be 110 deg and work for print.

  4. #4
    Retired 10,000+ Posts
    Ricoh C2003 - print job will do after re-close duplex unit

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,128
    Rep Power
    989

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Clean/check/replace the fusing thermopile unit. Located in the body of the C2003 just above the connector for the fusing unit. After removing the fusing unit two connectors and two screws to remove.

  5. #5
    Copier Technician 1,000+ Posts
    Ricoh C2003 - print job will do after re-close duplex unit

    mga's Avatar
    Join Date
    Dec 2010
    Location
    london
    Posts
    1,393
    Rep Power
    135

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Thermopile errors could also be given from faulty connections in fuser unit unplug all connectors ie thermistors etc and rear of main connector big blue one before reconnecting make sure no pins are push slightly out. Good luck
    Regards Mark

    FOR TRADE AND END USER SERVICE CALLS PLEASE VISIT WEB SITE FOR CONTACT DETAILS. COVERING GREATER LONDON {UK} AND ALL SURROUNDING COUNTIES.

    RICOH, CANON, KYOCERA, KONICA, SHARP, HP/SAMSUNG BROTHER, LEXMARK.

    https://copierservices.simdif.com

  6. #6
    Junior Member
    Join Date
    Oct 2020
    Location
    Taipei
    Posts
    4
    Rep Power
    0

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Thank you all for advice. Finally, i fixed it by clear counter of fuse.

  7. #7
    Service Manager 1,000+ Posts
    Join Date
    Oct 2011
    Location
    Hunter Valley, NSW
    Posts
    1,020
    Rep Power
    57

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Not permanent fix.

  8. #8
    Junior Member
    Join Date
    Oct 2020
    Location
    Taipei
    Posts
    4
    Rep Power
    0

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Quote Originally Posted by davel View Post
    Not permanent fix.

    indeed, because i have change every sensor and parts related with fuse and electric board.

  9. #9
    Service Manager 10,000+ Posts
    Ricoh C2003 - print job will do after re-close duplex unit

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    22,656
    Rep Power
    658

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Quote Originally Posted by NeoYoung View Post
    indeed, because i have change every sensor and parts related with fuse and electric board.
    ahhhhh the old 'shotgun' approach to repairing a unit. expensive.

  10. #10
    Retired 10,000+ Posts
    Ricoh C2003 - print job will do after re-close duplex unit

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,128
    Rep Power
    989

    Re: Ricoh C2003 - print job will do after re-close duplex unit

    Quote Originally Posted by Phil B. View Post
    ahhhhh the old 'shotgun' approach to repairing a unit. expensive.
    But sometimes necessary. Decades ago I worked on Vydec word processors. 20+ boards. A board could be within design specs on its output and the board it was talking to could be within design specs on its input but you could still get random errors if one board was to of extreme of the specs and the 2nd board to the other extreme. It was pick one and replace it. If that didn't work try the other. Tag the board with a description of the error. When I got the same error on 3 or more machines I would send the board to the repair depot. Component level techs had a list of what to replace passed on reported error.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here