Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Technician
    Join Date
    Mar 2010
    Posts
    37
    Rep Power
    29

    sc721-42 mpc5504 sr3220

    this error exists temporarily at the sorter. where is this motor on the parts catalog...? another idea what else could it be?
    gruss

  2. #2
    Retired 10,000+ Posts
    sc721-42 mpc5504 sr3220

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,126
    Rep Power
    989

    Re: sc721-42 mpc5504 sr3220

    Which finisher? Do not want to give you information for the wrong finisher.

  3. #3
    Service Manager 1,000+ Posts
    sc721-42 mpc5504 sr3220

    FrohnB's Avatar
    Join Date
    Jul 2017
    Location
    Nebraska, USA ------ GO BIG RED
    Posts
    1,919
    Rep Power
    126

    Re: sc721-42 mpc5504 sr3220

    SC721-42 B Stapler Retreat Motor Error
    During movement to home, the home position could not be detected withina predetermined pulse (1st time is jam notification, 2nd time is SCnotification)
    .
    During movement from home, the home position was detected even after a predetermined pulse elapsed (1st time is jam notification, 2nd time is SCnotification)
    .
    During movement from home, retreat sensor ON could not be detected even after a predetermined pulse elapsed (1st time is jam notification,2nd time is SC notification)
    .
    During initialization, retreat sensor ON was detected simultaneously when the home position is detected (1st time is jam notification, 2nd time is SC


    Could be a defective motor. The only 2 motors in the staple unit area are P/N: D5865640 and D6865630.
    Could be that the stapler unit is not moving freely and is putting extra load on the motor.
    Defective Home Position Sensor for the stapler unit.


    Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps.
    Check
    if the SC reoccurs by cycling the power after each step
    .
    The target parts are the motor and related HP sensor that SC occurred.
    1. Check if the connector of the target part is connected securely. Reconnectthe connector if it is disconnected, or loose.
    2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
    3. Check in input and output modes if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
    4. Check
    if there are any signs of a short circuit. Replace the parts if there are any defects.
    Omertà

  4. #4
    Service Manager 1,000+ Posts
    sc721-42 mpc5504 sr3220


    Join Date
    Nov 2007
    Location
    New Jersey
    Posts
    1,661
    Rep Power
    86

    Re: sc721-42 mpc5504 sr3220

    I've read that it can be caused by to wires going to the stapler pulling loose, caused from the stapler going back and forth. Sometimes the harness is a little short and pulled too tight.

  5. #5
    Technician
    Join Date
    Mar 2010
    Posts
    37
    Rep Power
    29

    Re: sc721-42 mpc5504 sr3220

    @slimslob sr3220
    yeh....i do order the 2 motors and the wire.
    I hope it helps...let me know then

  6. #6
    Retired 10,000+ Posts
    sc721-42 mpc5504 sr3220

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,126
    Rep Power
    989

    Re: sc721-42 mpc5504 sr3220

    Quote Originally Posted by hanspeter75 View Post
    @slimslob sr3220
    yeh....i do order the 2 motors and the wire.
    I hope it helps...let me know then
    If you have the C5504 service manual both the motor and the retreat sensor are shown in the Stapler displacement mechanism portion of the section on the finisher. I hope that is one of the motors you ordered. The sensor could also be the problem.

  7. #7
    Field Supervisor 500+ Posts Zaxxon's Avatar
    Join Date
    Jan 2014
    Posts
    607
    Rep Power
    36

    Re: sc721-42 mpc5504 sr3220

    Check if the lock pin is bend (the one holding the unit locked when paper jammed).
    Please start you post with brand, model, problem.

  8. #8
    Technician
    Join Date
    Mar 2010
    Posts
    37
    Rep Power
    29

    Re: sc721-42 mpc5504 sr3220

    I do not quite understand?

  9. #9
    Service Manager 1,000+ Posts Gift's Avatar
    Join Date
    Mar 2011
    Location
    Gothenburg
    Posts
    2,316
    Rep Power
    86

    Re: sc721-42 mpc5504 sr3220

    I'll give the stapler harness a +1, we had quite a few ones going faulty

  10. #10
    Field Supervisor 500+ Posts Zaxxon's Avatar
    Join Date
    Jan 2014
    Posts
    607
    Rep Power
    36

    Re: sc721-42 mpc5504 sr3220

    Quote Originally Posted by hanspeter75 View Post
    I do not quite understand?
    There is a little metal pin/pahl holding the entire drawer locked, when machine runs. This pin can be bend and cause sc721-42
    Please start you post with brand, model, problem.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here