Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 17
  1. #1
    Senior Tech 250+ Posts daveyball's Avatar
    Join Date
    May 2009
    Location
    Douglas
    Posts
    314
    Rep Power
    28

    Mp9000 we end error

    Hi

    I have e MP9000, with intermittent replace cleaning we errors, the web is no where near the end on all occasions.

    Any ideas

  2. #2
    Professional Moron 2,500+ Posts TonerMunkeh's Avatar
    Join Date
    Apr 2008
    Location
    Shitsville, UK
    Posts
    3,589
    Rep Power
    91
    Is the web consumption / near end set to a silly value? Paper in the fuser connector? Is the machine generating an SC or just saying it's web is near end? Might be the web end sensor is twitchy.

  3. #3
    Senior Tech 250+ Posts daveyball's Avatar
    Join Date
    May 2009
    Location
    Douglas
    Posts
    314
    Rep Power
    28
    The web end sensor(s) have been replaced, the machine is displaying web near end or replace web, we just reset it and it goes away for a while

  4. #4
    Professional Moron 2,500+ Posts TonerMunkeh's Avatar
    Join Date
    Apr 2008
    Location
    Shitsville, UK
    Posts
    3,589
    Rep Power
    91
    What's the web value of SP1902 at when the machine says near end?

  5. #5
    Senior Tech 250+ Posts daveyball's Avatar
    Join Date
    May 2009
    Location
    Douglas
    Posts
    314
    Rep Power
    28
    The web vaule said 16, and about half the web was still fresh

  6. #6
    Field Supervisor 2,500+ Posts
    Mp9000 we end error

    Jomama46's Avatar
    Join Date
    Apr 2008
    Location
    Fairfax, VA
    Posts
    2,905
    Rep Power
    61
    I'm guessing you know that the 9001 uses a different web than the 6/7/8001.

    You never realize how cheap a professional is until after you let an amateur do it.
    A+; Network +; PDI+

  7. #7
    Senior Tech 250+ Posts daveyball's Avatar
    Join Date
    May 2009
    Location
    Douglas
    Posts
    314
    Rep Power
    28
    Yes we are using the 9000/1105 web

  8. #8
    Field Supervisor 500+ Posts
    Join Date
    Apr 2010
    Location
    the west
    Posts
    665
    Rep Power
    32
    Is the web end feeler installed correctly? I have seen it many times where it is on the wrong side of the web and this shows an end when about 50% is left.

  9. #9
    FORMER Techie 1,000+ Posts tcs04's Avatar
    Join Date
    Apr 2009
    Posts
    1,191
    Rep Power
    37
    Quote Originally Posted by daveyball View Post
    Yes we are using the 9000/1105 web
    I THINK there was a firmware update... BUT also.. jonhiker could be correct... is the machine showing "web end, sc 550(?) or near end?l

    If web end jonhiker is correct and the acuator is set in the wrong position. it should be OVER the SINGLE layer of web leaving the "full" roll, otherwise it will normally fall past the roll at about 35% - 45% life.

  10. #10
    Trusted Tech 50+ Posts
    Join Date
    Aug 2008
    Posts
    66
    Rep Power
    27
    Yep, had the same one. Copier has the latest FW. After resetting 1902 and inserting the previous value copier was working. The web motor/sensor replacing didn't help. I cleaned the fuser's plug and the second one on the wall, copier still working without issue. But this is nonsense, it looks like fw/board issue.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here