Just posted a question on the vid.[emoji41][emoji1303]
Sent from my SM-N950U1 using Tapatalk
Type: Posts; User: qbert69
Just posted a question on the vid.[emoji41][emoji1303]
Sent from my SM-N950U1 using Tapatalk
Screw Teflon...why not Ceramic non-stick???[emoji848]
Sent from my SM-N950U1 using Tapatalk
Rudolf Diesel likes .22 Springers & Vaseline Dabs!!![emoji1787][emoji38][emoji23]
Sent from my SM-N950U1 using Tapatalk
Not much to say here, other than...This is EXTENSIVE INFORMATION!!![emoji15]
https://weathermodificationhistory.com/
Sent from my SM-N950U1 using Tapatalk
Choose the settings you like in scan mode then go into system settings->user settings->scan settings ->set current as default (should lock it in...not in front of a machine right now!)
Good...
SCANNING BRAH!!! *NOT* PRINTING!!!
...check your linky!!![emoji57]
Sent from my SM-N950U1 using Tapatalk
Yep!!! End user doesn't realize that all the pagination is done in the print driver!!!...and because of that, the double page spread layout doesn't work the way they expect it to!!!...single pages...
Brand of machine???[emoji848]
Sent from my SM-N950U1 using Tapatalk
Lady! LET THE G0DD@MNED GEL PEN INK DRY BEFORE RUNNING IT THRU THE ADF!!![emoji2959][emoji23][emoji38][emoji1787]
...do an ink dry time smear test right in front of her!!! Gel ink vs standard ball...
Print driver presets within the print driver. Some manufacturers allow you to save the presets to a folder. Once all presets are saved to the folder, the folder of presets can be copied to a server...
Pay Attention!!!
TLAVagabond * DLive
Sent from my SM-N950U1 using Tapatalk
A definite note that dirty/contaminated laser slit glass can create a "soft", meaning de-registered and lightened image due to the dust/toner "scattering" the write beam on the drum...
Any rubber feed rollers that are dusted with paper dust or glossed over that need to be cleaned with rubber cleaner???[emoji848] sometimes slippage can occur from dirty/fouled feed rollers!!! Can...
I've seen the "fade" or non-existent color happen if the dev unit of a particular color is not aligned properly with the drum so that the developer mag roller with toner on it can properly brush...
IDC sensor usually at the end of the ITB, just below it and above the registration roller. I've also seen them right above the ITB, right before the fuser...usually a solenoid actuated shutter...
Spot On!!! We had some 808's that had about 1.5 million copies on them that were misfeeding... took out feed units and where the one way bearings are, the shafts were polished SLICK!!! Slick shaft =...
Laptop <---Crossover Cable--->MFP!!! DERP![emoji2957]
Is the paper that's "jamming" glossy, heavy, brochure stock by chance???[emoji848]
Sent from my SM-N950U1 using Tapatalk
It's ALWAYS going to throw the "caution hot fuser" message!!! It's warning you that it's HOTTT!!! DERP!!![emoji2957] Use your Noodle!!! If it's "always jamming", check to make sure the paper medium...
Is it true black or is it process (C,M,Y) black??? Is there a sensitivity adjustment in the print driver to bias the detection either towards true black/grayscale or the opposite direction of process...
Do an error code reset during startup but instead of doing an error clear, enter the service code to access service and then go to clear all the settings & reset the admin password. Should...
See if autocad has a flatten before sending to print function...other than that I have no other suggestions. It all boils down to the end user knowing WHY their file is spooling so...
The image is multi- layered and not flattened...use a program such as Bullzip to flatten into a single layer PDF before sending to the printer...[emoji57]
Sent from my SM-N950U1 using Tapatalk
Possible fuser drive/power sense board issue I'm guessing...are you able to monitor for proper fuser temps???[emoji848]...just because thermistors are clean doesn't mean the fuser is driven to the...
Warming up....sounds like a fuser issue. Check to make sure fuser thermistors are clean...Additionally, might there be a fuser drive board issue??? Just thinking....[emoji848]
Sent from my...