I've had to replace the Primary transfer unit when having multiple dv pull issues on these machines. Also make sure the transfer charge connection springs and plate on the rear side of the primary...
Type: Posts; User: Andypraeuner
I've had to replace the Primary transfer unit when having multiple dv pull issues on these machines. Also make sure the transfer charge connection springs and plate on the rear side of the primary...
I have had some luck changing the heat setting in sim 43-1 on plain paper to +10 and also upgrading the firmware to current and setting the machine to auto run the fuser clean mode at different...
I had a MX3071 do the same thing a couple years ago turned out that the fuser drive, transfer drive, and delivery drive units were loose because the screw points in the frame were cracked, like the...
Doug if you can find a right side hinge just clip the 2 fins off the bottom of that hinge and it will fit fine. Also these hinges are used on the MXC311-312 if you can find one of those to steal from.
There was for a short time a kit that could be ordered to add a cleaning web roller kit that could be added to these fusers. That was shortly discontinued since it was mostly useless. So they have a...
The MXM6570/MXM7570 are solid and great running machines. We have some in schools and 1 in a printing company. The one in the printing company had 9852 prints in the first week of operation before...
Luke123, I know this post is from over a year ago but do you remember how/if you retimed that unit? I'm guessing since you said it was not easy that a firmware upgrade will not fix it.
How did you accomplish this? Did you have to order software or any parts? If so what did you have to order or install?
I do have a MXM363N that still has the MFPC PWB, the mother PWB and the PCU PWB, would that be a place to start? Im guessing if I take those pwb's that I will have to swapp EEPROMS and reflash...
Is it possible to convert a MXM363U into a Network machine? I have a MXM363N that I can rob parts from with the proper guidance.
The double tap of the home button should be fairly brisk and quick or it will think you are just holding the home button which will just give you the copy count screen which will go away in a few...
Check the sensor actuator in case someone in the office had a jam and pulled the paper back out and dislodged the SPPD1 actuator.
From what I have heard from our department coordinator sharp is getting out of the parts and transfering all parts to a company called Tech Data.
I just had a nonresponsive screen on a MX2616. I had trouble getting into sims but when i did i ran sim 65-1 to readjust the touch screen then did a firmware upgrade. That worked for about a week...
Ya they aren't too easy, I have had to replace quite a few with the new updated board due to the C4-00 code. Part # RDENU0154FCP2
Tried it once by accident and it didn't work.
FYI update. When I arrived on site I had a few ideas on what to look at first, second, third...etc. Discovered that none of these were the problem. The customer had removed a jam after the machine...
Just an update FYI, I replaced the fuser to fix the false FK3 on the screen, we new that the count was not up since the copier has less than 100k copies total. So far the false reading has not come...
I have a MX2616N that has been posting a FK3 code on the copier screen but will not send us the alert while we are recieving all other alerts from this machine. We have upgraded the firmware and...
I have a MX3140N that the customer called and said she was printing checks from the by-pass tray when it jammed and showed the L4-12 code.
When she removed the jam and closed the door to continue...
Do a black shy shot, if you get zebra striping all accross the page you have a developer pull situation and you will need to rebuild the drum unit and replace the developer. Also check the seals on...
I agree with Harleyrider and have seen this as well. The secondary transfer is catching in its rotation and will cause this. While you are in there check to make sure the primary transfer drive gear...
OOOOOMGG thanx ZOOTECH for getting my mind and eyes back in focus.
If anyone can point me in the right direction, I have replaced the upper roller thermoster, the lower roller thermoster, and the uncontact thermoster. I am getting this code every time on a new...
are the MX36NUSA and MX36NUSB interchangable