"WE need a new machine" I hear it all the time. my reply is always the same "I'm giving you a new machine 1 part at a time"
Type: Posts; User: ssbmi
"WE need a new machine" I hear it all the time. my reply is always the same "I'm giving you a new machine 1 part at a time"
Another tech, had this code on a mx3100n, after changing out the parts listed in manual
, with out problem being solved. He changed out the DC-pwb. problem solved
Had the same code on a mx3100n, changed out the same parts as you, no joy. Went on to the dc-pwb. Fixed our problem.
ok, changed out scanner control board, also changed out pcu pwb. Still no change. I have no direction or idea where to go next. ;(
ANY HELP, anybody have this problem before.?
Thanks for the idea.. I tried the display panel from a mx-m 550. no joy, problem still the same.
I am working on a MX-M 700n. My problem is mfp will not power back on once it has been turned off with the power switch(outside switch). Unless reset using the main power switch(inside switch)...
We were going to change number to number that matches our file, but since it only matters to us. We gonna change the number in our file to match the machine. thanks from Kauai!
new number not replacing present number. Is there another thing I should be doing? Thanks in advance for any help.
[QUOTE=ssbmi;415232]Mahalo to all of you for sharing your information.
It was their network. I disconnected from the network. No more freezing up. Had their It guy check their network, and let...
If your still having this problem, I cured our mxm700 of freezing up by unplugging the 700 from the network. To get it to work right I then set their IT guy to update the printer driver, and check...
Mahalo to all of you for sharing your information.
Ok here is where I'm at with the 700, we have changed out the rom chips(because of freezing problem during firmware up grade). changed out boards: pcu, controller, mother. found out the dedicated...
not yet, this problem has now turned into a intermitted problem since I last reset the thermostat, and cleared the code. I haven't been called back. But since I haven't fixed anything. its still...
for the first code customer said they did heavy paper, after I changed fuser. 2nd code the next day customer said it was just plain paper... and that was with the rebuilt fuser.
I got a mx-m550, h4-01 code. changed out fuser with a rebuilt fuser. same code next day. checked fans both working. going to boards next. or is there something I should be doing first? was there a...
thanks for the info, and direction. I'm gonna try the Version up procedure 3.. sounds like my troubles all the way.! again MAHALOs and ALOHA!..I never even do anything yet but when you at least...
I'm working on a mxm700, that's started to freeze up for no reason. I changed the pcu pwb, the problem went away for about a week, but came back, so I changed out the control board it froze up in...
Voila!! Got it going after 2 tries.. Thanks buddy!!!
Yes and Yes. I tried 'um both. Both the driver packages on the IDNC site for the 64 bit os. Maybe not praying hard euff??
I have a ARM207 that I have been trying to install with a USB cable. Only a 1 desk office. This is usually a plug and play install. But No joy. I had to down load the driver from Sharp/idnc. ...
I found the problem.. ADU was out of place by 1/16th inch towards back of machine. I noticed the 1/16th in adjust markings on the hinges of the ADU. Adjusted the ADU 1/16th inch towards the front...
I've been working on a AR-651. copies great from platen. But as soon as I use the ADF on dbl sided or single sided copies. I get a shadow on the front half of copy, from lead edge to trailing edge.?...
I am working on a AR-651, the problem is an almost imperceptible waviness on all horizontal lines only. Anybody have this problem before? Any ideas will be looked into.
Thanks Bylyahn, now to proceed!
Sorry, I should have also included the Sharp parts guide that I am using. SHARP PARTS GUIDE, MODEL AR-651/810, CODE: 00ZAR810. They list it on the IDNC site. But not the P1(parts guide). This is...