Search:

Type: Posts; User: Elmtech

Page 1 of 7 1 2 3 4

Search: Search took 0.14 seconds.

  1. Thread: dcp 2540

    by Elmtech
    Replies
    2
    Views
    3,185

    Re: dcp 2540

    Needs the raw firmware file loaded. That can be obtained from an Authorised Brother Dealer along with the utility to load it.
  2. [CQ] Re: Brother MFC L5900 Light copies when copying off glass (Prints fine from PC)

    If you execute maintenance mode function 55 this initializes the white level data for the CIS.
  3. Replies
    5
    Views
    855

    [CQ] Re: FS-9530DN White Lines

    Also may be worth checking the laser glass
  4. Replies
    8
    Views
    2,002

    [Jamming] Re: Brother MFC-J5910 dw paper jam

    Possibly a fault on the carriage pcb. It has a sensor for detecting the edge of the page.
  5. Replies
    15
    Views
    1,500

    Re: Ricoh AF 3025 Ghosting

    Thanks all the resonses. I reattended today and threw some powder on the drum blade. Also changed the dev bias voltage to -600. So far so good
  6. Replies
    15
    Views
    1,500

    Re: Ricoh AF 3025 Ghosting

    I did run the developer initialization to calibrate it. All was lrinting perfectly while i was there. I did not supply the parts for this job was given them by the boss. Just fitting what i was...
  7. Replies
    15
    Views
    1,500

    Re: Ricoh AF 3025 Ghosting

    Thanks for all the information so far. The whole drum unit / imaging unit including new developer powder was replaced and installed according to the service manual. The ghosting issue was not present...
  8. Replies
    15
    Views
    1,500

    Ricoh AF 3025 Ghosting

    Hello,

    I have ricoh af3025 which had a line in the feed direction on prints. Found it was the pcu. After replacing the pcu with a new genuine part and new developer everything was working ok....
  9. Re: Lexmark MX711de printing light greyscale in the middle of the page

    Tray cleaning the laser unit glass. Had this several times.
  10. Replies
    4
    Views
    2,812

    Re: Firmware for a Canon IR C5240

    Ty for the reply. Will try it tommorrow.
  11. Re: HPLJ M602 Blank Control Panel, non-functioning power button.

    Backlight on panel but no characters on an HP usually means a problem with the memory or firmware. Can you do an engine test? Try it with the formatter removed aswell. Atleast this will separate the...
  12. Replies
    4
    Views
    2,812

    Firmware for a Canon IR C5240

    Hello,

    Is there any chance of someone supplying me with firmware for a Canon IR-C5240 it is to repair an issue with the scanner producing scans/ copies with almostvhalf the page black. It was...
  13. Replies
    1
    Views
    1,131

    Re: Lexmark C925 - control panel blank

    From memory if Lexmark machines detect a problem with th operator panel it will beep 5 times at boot up. If it is not doing this could be a board issue.
  14. Replies
    3
    Views
    1,637

    Re: MFC-5720DW Phantom Jamb at power on

    Yeah thats the one underneath the carriage pcb. They can be a pain in the ass and tbh i have never had that sensor fail on that model.
  15. Replies
    3
    Views
    1,637

    Re: MFC-5720DW Phantom Jamb at power on

    Possible comtamination on the encoder carriage movement or paper feed. Also possibly paper width sensor on the carriage PCB.
  16. Replies
    5
    Views
    2,270

    Re: clj 3800 54. xx codes

    Have you checked the left and right cartridge locks and lock lever slides? Also the alignment of the main drive might be causing it.
  17. [Misc] Re: Oki ES5461 claims toner empty after drum kit replacement

    What drums were replaced? ES series oki machines use the same drums and toners as the regular Mc range except the chips r different. That could possibly cause the issue.
  18. Thread: Paper Curling

    by Elmtech
    Replies
    9
    Views
    2,198

    Re: Paper Curling

    Have you tried updating the firaw are? Also have you tried a different brand of paper. Lastly check there is decent airflow for the machine to vent heat especially the rhs of the machine.
  19. Replies
    6
    Views
    1,143

    Re: HP 4014 not feeding paper

    The symptom theengel is the machine says there is no paper in the tray even though there is. Had several calls like that.
  20. Re: cp2025 sometimes will have blanks areas where colors should be----black always ok

    Would look at the color dev engagement sensor on the main drive and the solenoid as well. May be sticking.
  21. Replies
    11
    Views
    2,392

    Re: HP 4000 jamming

    I usually put a piece of electrical tape between the magnet and arm. Solenoid is louder but never sticks again
  22. Replies
    4
    Views
    767

    Re: P3015 Copy Quality

    Have you tried different paper stock? Fresh ream or different brand.
  23. Replies
    2
    Views
    1,585

    Re: L6200 Wifi problem

    Try updating the firmware.
  24. Thread: BH951 Black

    by Elmtech
    Replies
    8
    Views
    851

    [CQ] Re: BH951 Black

    Have you checked the laser unit for dirt?
  25. [CQ] Re: brown looking 1/2inc line on page hp 9500n

    If its brown its most likely a problem with the transfer belt cleaning assy. Check the cleaning blade and replace if needed.
Results 1 to 25 of 155
Page 1 of 7 1 2 3 4