I tried rolling back firmware on this model. No matter what I tried, it wouldn't let me roll it back. The screen kept telling me it had the newest firmware and that was the end of the story.
Type: Posts; User: tmw
I tried rolling back firmware on this model. No matter what I tried, it wouldn't let me roll it back. The screen kept telling me it had the newest firmware and that was the end of the story.
We had one like that. Ended up replacing the fuser harness. Haven't heard back since with that code. One of the pins could be damaged enough to keep coding out. It's not too terribly hard to change....
I am updating in case if someone needs a future reference. I installed a bundle board being the next thing in the manual. The first time I tried loading the roll it said it wasn't recognized. I...
I was wondering if anyone had problems trying to flash firmware to the T520. the HP site started the process. The boxes popped up showing it was extracting the files. The customer had to enter her...
As I said in the original post, I got the driver from Kyocera. I used the one available for mac. As far as I can tell it went the same as it showed in the supplied video. I also was generally looking...
Hi, I was hoping someone more familiar then myself can enlighten me on this question. I have installed drivers on macs successfully before, but I'm not as familiar navigating them. I still may be...
Sounds like you may need to replace adf/scanner assy. Unfortunately individual parts aren't available.
I think it's a poor design. It should use a proper auger instead of a coiled wire.
I think a 57 error refers to a fan. The last set of numbers should indicate which one it is.
I'm sorry if this is late. I have had a couple T2500s that would have trouble installing a new print head. It was down to either the purge unit or the service station being bad. I don't remember the...
The 3571 takes an EMMC card. It is half the size of an Msata. Be sure to have the correct one. Can you see any image on the screen if you hold a flashlight against it ? One problem I hope you don't...
This is turning out to be an odd one in my opinion. Just to be clear it is the SCN MFPC board. It integrates the network board. I tried all your suggestions. Except we don't have another 3070 at the...
Tending to think it's something electronic. I haven't tried the sim yet. My fellow tech started to check it out. He noticed it was starting to give the please wait message and freezing up. He...
I haven't seen thousands of these machines yet. On the ones I have, the msata/emmc card can be a weak point. It seems the fuser problems they were having has calmed down.
I don't expect anyone to solve this for me, but if it jogs your memory or have a hint of anything it would be greatly appreciated. We got a repaired scn board back from hytec that was sent for boot...
He's going to die someday. Then what ?
We just had a 4071 fuser making noise. Replacing the pressure roller bearings took care of it. Unfortunately if it's the other bearings, they can't be replaced. (easily)
I only have a description of this problem to go by. I was there twice, one time right after they said it did it. Each time I could not reproduce the problem.
They report that occasionally when...
After testing with a different machine at the office, it seems that the surge protector may be faulty. Has similar random shut down events.
Called to look at brand new machine we just installed. Found it odd that misfeeding was being reported already. I was running it without a problem, then suddenly it appeared that it shut off with...
"Flakey white stuff". I get a kick out of him.
Is the stripe in the exact same place from both cartridges ? You could have two bad carts. The pattern looks random and not repeating. I tend to think it might be electrical. Maybe a contact isn't...
Although it's rare, I have seen a faulty system board cause random thin lines. Maybe reseat the board and whatever chips that may be installed on it. Might help eliminate it. Or possibly the ribbon...
Any machine that displays this code. In this case mx-m363, but it can appear on any model.
Would anyone, even Sharp be able to tell how you can tell the difference between boards that say they are mismatched. So far trying to decipher markings or anything that might seem different. The...