I've had this before. I'd bet my house it is laser glass. Cleaning tool does not get it clean as the time I had it there was a sticky substance on the glass. Had to remove laser assy to clean it...
Type: Posts; User: printerguy77
I've had this before. I'd bet my house it is laser glass. Cleaning tool does not get it clean as the time I had it there was a sticky substance on the glass. Had to remove laser assy to clean it...
[QUOTE=copytechman;732458]I had a c287 (same series) with this issue, it was the emmc board for ours.
Regards
A.[/QUOTE
Same here with regard to the eMMC board on a Olivetti MF223 / Konica...
Ok. Thanks for that. Is that done in the U modes? I can't see any reference to simulation modes in service manual.
Hi guys
I have the same issue here. I'm ordering the new ssd board. What do you mean by doing simulation 04 "machine model" I'm unfamiliar with this machine please explain.
Once again just a new point on these jam codes. Also was getting 3201 jams. Only thing was that this was very intermittent. Could sometimes get 300 sheets between jams. Most common was 3003. Tried...
on the sample which is the direction of paper feed?
definately a cyan issue with either developer or drum. start there. have had issues with ITB also where the customer does not change waste toner...
I'd hazard a guess that you are using compatable toners and probably Katun at that.
this nearly destroyed my fleet of Olivetti MF222 -MF452. do not use it under any circumstances. savings are not...
Thanks for your input. Allegedly so does the compatable.
Hello all.
Just wondering ing if anyone is using Katun performance toners on the 224 range.
We we have been using it on this machine and the Olivetti equivalent and it's causing a lot of PCQ...
Hi All.
did this get resolved and if so what was the solution.
i have a same issue on a 454e but only seemed to start after i replaced the Developer unit.
had to replace as my boss thought...
This is great. had a Canon GP605 (i think) that at mid morning the sun was shining through the window that the printer was sitting beside .it shone through the vent slits on the copiers side panel...
If you look closer at the toner levels on the sample you submitted you will see that the yellow and magenta are also out of alignment.
i also have the same issue on same device. i have replaced...
Having a similar issue with both trays. does anyone know what the fix for this particular problem was?
I've had the developer unit out several times at this stage. I have just requested a new prcb. Fingers crossed. I have changed the toner low sensor and swapped the hopper drive motor also. These damn...
By the 2 ids sensors I presume you mean the sensors on the transfer belt. These are clean but have nothing to do with tcr control. My cyan is reading 0.00 in service mode and the other 3 colours are...
Hi All,
i have the above error code and the cyan dev unit was just at end of life so i replaced it and the fault cleared, that was about 3 weeks ago and it has now come back with the same error...
Excuse my ignorance my friend but first I have heard of this. I know of connecting to the machine through the remote user interface. Where do I switch of the csrc?
Hi rohan. Can you let me know what you mean. What is the csrc? Do you mean still connected to the web browser? Thanks
Thanks mrwho.
As as it says on original thread. Screen says "ready to copy". But start button flashes orange. Machine will not print scan or copy
Hi All. have a olivetti MF45 same as the KM c450.
Had an c2651 error code and machine saying the cyan dev unit not seated properly.
sent in a 2nd hand unit and the machine seemed fine and came to...
you seem to have less options on your machine than i have on mine. try using a different web browser like chrome maybe.
Im sure you have tried this. log onto web browser-go to network-email settings-email tx smtp settings-at the top of the page make sure you have enabled counter and notification settings.
i cant...
Hi All sorry to jump in on this thread. i am having the same issue with the Olivetti equivalent of the task alfa 3500i. it is stuck in the J0000 and it will not clear. my engineer in belfast has been...
You more than likely have to reload system software and patches to the C 1 if you can't see it. Also make sure you have ing-cnt set to 3 in service mode.
This one looks like it is laser related. Definitions between white and black are to fine to be HVT